Strain Gage
Mostrando 1-12 de 22 artigos, teses e dissertações.
-
1. Experimental Study of Fatigue Crack Behavior of Rib-To-Rib Butt Welded Connections in Orthotropic Steel Decks
Abstract Rib-to-rib (RR) butt welded connections are one of the most sensitive locations for encountering fatigue failure in orthotropic steel decks (OSDs), and numerous fatigue cracks arising from these areas have been identified in existing OSD bridges. Due to dynamic factors in their service life bridges with an orthotropic steel deck (OSD) are prone to f
Lat. Am. j. solids struct.. Publicado em: 11/10/2018
-
2. Experimental investigation of mixed-mode-I/II fracture in polymer mortars using digital image correlation method
The purpose of this work is to investigate experimentally the effects of mixed-mode I/II loading on the fracture behavior of polymer mortars. Three point bend beam specimens with offcenter notch were used in plane-strain fracture toughness tests. Two approaches have been simultaneously used to determine the crack opening displacements. The crack mouth openin
Lat. Am. j. solids struct.. Publicado em: 2014-03
-
3. Medição de tensões residuais em poliestireno pelo método do furo cego / Residual stress measurement in polystyrene through the hole drilling technique
Tensões residuais em peças poliméricas são grande fonte de incertezas para o projeto de componentes industriais. São causadas principalmente durante o processo de injeção. Alguns dos problemas relacionados a esse fenômeno são a diminuição da resistência mecânica, surgimento de trincas e empenamento das peças. Muitos esforços são empregados na
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 15/12/2011
-
4. Influência do tipo de medição na determinação do módulo estático de elasticidade do concreto / Influence of Type of Measurement in Determining the Static Module of Elasticity of Concrete
O conhecimento da resistência à compressão e do módulo estático de elasticidade é fundamental para o estudo das deformações do concreto, uma vez que as deformações podem gerar fissuras capazes de comprometer tanto o comportamento estrutural do elemento de concreto, como servir de caminho de entrada aos agentes deletérios. Não só fissuras, mas ta
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 15/08/2011
-
5. Avaliação da deformação do intermediário e região peri-implantar em função da carga aplicada em coroas unitárias implantossuportadas parafusadas / Evaluation of the deformation in the abutment and peri-implant region according to the load applied in screwed implant-supported single crowns
As coroas unitárias metalocerámicas implantossuportadas são amplamente utilizadas na reabilitação de pacientes desdentados. O comportamento mecânico destas coroas é muito importante para entender o processo de transmissão de forças mastigatórias e suas reações no intermediário e na estrutura óssea peri-implantar, mas estes processos ainda não
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 30/05/2011
-
6. Experimental and theoretical study of a telemetric dynamic torque meter
This paper presents the development of a dynamic torque meter to be applied to rotating shafts using electronic transduction, strain gage, telemetry and LabView Graphic programming. A mathematical model was developed. The electronic transduction signal is transmitted by digital modulation from a remote transduction unit fixed to a shaft to a base station, se
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2010-09
-
7. A multi-scale investigation of the mechanical behavior of durable sisal fiber cement composites
Durable sisal fiber cement composites reinforced with long unidirectional aligned fibers were developed and their mechanical behavior was characterized in a multi-scale level. Tensile tests were performed in individual sisal fibers. Weibull statistics were used to quantify the degree of variability in fiber strength at different gage lengths. The fiber-matri
Matéria (Rio de Janeiro). Publicado em: 2010
-
8. Avaliação experimental e teórica do torque no laminador de chapas grossas da Usiminas
A laminação controlada constitui-se em um efetivo meio de produzir aços com alta resistência mecânica e alta tenacidade. Ela é utilizada em laminadores de Chapas Grossas de todo o mundo para produzir chapas de alta resistência para navios, aços graus API destinados a tubos, bem como outros aços estruturais. O principal objetivo da laminação contro
Publicado em: 2010
-
9. Desajuste marginal e influencia na pre-carga de parafusos e nas tensões induzidas as fixações de pilares metaloplasticos sobre-fundidos / Marginal misfit and influence in the pre-load and the stress-induced setting of the metaloplastic abutments
Castable UCLA abutments are of wide applicability in dental implants, because they allow the manipulation in the laboratory at low cost and individualization of abutments for each patient. However, they show the worse results of marginal adaptation then the fabricated, although these aggregate costs significantly higher. UCLA premachined abutments for castin
Publicado em: 2010
-
10. Efeito de Concentração de Tensão na Vida em Fadiga de Aço Utilizado em Spindle de Laminador de Chapas Grossas Análise Experimental e Modelamento via MEF
Due to the high number of failures of the USIMINAS company Plate Mills spindle, it was necessary a careful evaluation in order to determine the causes responsable for the failure. Through the use of the Root Cause Analysis technique, it was established that one of the main factors causing the failures was the fatigue phenomena. After engineering analysis and
Publicado em: 2008
-
11. Evaluation through the mgnetic inspection of the superficial condition of steel bearing rings DIN 100Cr6 after hard and dry turning. / Avaliação através da inspeção magnética da condição superficial de anéis de rolamento de aço DIN 100Cr6 após torneamento duro a seco.
The present work presents information for the manufacturing of ball bearings components with higher limits of resistance to fatigue, enabling a longer useful life and also the optimization of the production of the pieces, making the usual and final process of grinding unnecessary, which would result in a costs reduction. The motivations of this study are the
Publicado em: 2008
-
12. Study of cutting forces in the edge milling process of sheets used on welded pipes manufacturing. / Estudo das forças de corte no processo de fresamento de bordas de chapas utilizadas para a fabricação de tubos de aço com costura.
O propósito deste trabalho é estudar as forças de corte envolvidas no processo de fresamento de bordas de chapas utilizadas para a fabricação de tubos de aço com costura e como estas variam em função dos parâmetros de corte utilizados. O objetivo é correlacionar estas forças à qualidade do acabamento superficial das bordas usinadas, uma vez que e
Publicado em: 2007