Machining
Mostrando 25-36 de 254 artigos, teses e dissertações.
-
25. Investigation of High-Speed Cryogenic Machining Based on Finite Element Approach
Abstract The simulation of cryogenic machining process because of using a three-dimensional model and high process duration time in the finite element method, have been studied rarely. In this study, to overcome this limitation, a 2.5D finite element model using the commercial finite element software ABAQUS has been developed for the cryogenic machining proc
Lat. Am. j. solids struct.. Publicado em: 2017-03
-
26. Surface Integrity Analysis in Machining of Hardened AISI 4140 Steel
This study aimed to analyze the residual stresses and roughness in finishing milling of AISI 4140 steel, quenched and tempered up to hardness of 58 HRC. Machining operations were performed with the use of CBN inserts and by varying three basic cutting parameters (cutting speed, feed per tooth and cutting depth). Hardened materials are typically machined by a
Mat. Res.. Publicado em: 23/01/2017
-
27. Development and Test of an Equipment to Measure Residual Strain Inside Pipes Using the Hole-Drilling Method
Abstract Residual stresses are present in materials or structural component in the absence of external loads or changes in temperatures. The most common causes of residual stresses being present are the manufacturing or assembling processes. All manufacturing processes, such as casting, welding, machining, moulding, heat treatment, etc, introduces residual s
Lat. Am. j. solids struct.. Publicado em: 2016-12
-
28. A Comparative Study of Joint Clearance Effects on Dynamic Behavior of Planar Multibody Mechanical Systems
Abstract Clearance always exists in actual joint due to many uncertainties such as machining tolerance, assemblage and load deformation. The main purpose of this paper is to propose a computational and experimental study on the dynamic characteristics of a planar multibody mechanical system with joint clearance. For this purpose, a suitable dynamic model pla
Lat. Am. j. solids struct.. Publicado em: 2016-12
-
29. Effect of Cold Work on Cavitation Resistance of an Austenitic Stainless Steel Coating
Abstract Machining procedures of welding deposits are usual and result on cold work hardened surfaces. The cold work effect on cavitation erosion of an austenitic stainless steel surface is assessed. FeCrMnSiB coatings were processed by PTA on AISI 304 plates. Specimens were grouped as the cold work deformed surface (CWHS) and the undeformed polished surface
Mat. Res.. Publicado em: 01/08/2016
-
30. Evolución Microestructural en Uniones de la Aleación Ti-6Al-4V Mediante el Proceso de Soldadura de Punto por Fricción-agitación
Abstract Friction stir spot welding (FSSW) is a process of recent development and interest, mainly in titanium alloys, since there are previous studies of aluminum alloys, magnesium, steel and polymers. Titanium alloys have a wide range of applications in the aeronautical industry, mainly in the components of commercial aircrafts as landing gear. Therefore,
Soldag. insp.. Publicado em: 2016-06
-
31. Machinability Evaluation in Hard Milling of AISI D2 Steel
Milling of hardened steel components provides considerable benefits in terms of reduced manufacturing cost and time compared to traditional machining. Temperature variation in milling is an important factor affecting the wear of cutting tools. The poor selection of milling parameters may cause excessive tool wear and increased work surface roughness. Hence,
Mat. Res.. Publicado em: 01/03/2016
-
32. Methods of data analysis for the ball cratering test on TiN and DLC coated steel
Titanium nitride (TiN) coatings are widely used in machining because of its mechanical characteristics which modify the surface of the substrate increasing the capacity of load support and reduction of friction, while a coating as diamond-like carbon (DLC), which also has interesting mechanical properties, needs better attention. In this sense, the developme
Mat. Res.. Publicado em: 05/02/2016
-
33. The Influence of Twist Drill Main Cutting Edge Preparation in Drilling Process
In order to improve the performance of a twist drill, one must understand some aspects involved in drilling process that are not commonly addressed, such as the micro geometry employed in the tool’s tip sharpening and the protection of the main cutting edge. The edge of the twist drill can be protected by rounding, chamfering or the combination of both. Th
Mat. Res.. Publicado em: 17/11/2015
-
34. Location Issues of Thin Shell Parts in the Reconfigurable Fixture for Trimming Operation
ABSTRACT: The location of thin shell parts is always a knotty problem during machining, welding, forming, assembling and inspection operations. This paper mainly focuses on the special location issues in the digital and flexible trimming process for aircraft skins fastened by reconfigurable fixture. Firstly, in view of the dynamic change of effective locator
J. Aerosp. Technol. Manag.. Publicado em: 2014-09
-
35. Analysis of surface roughness and hardness in titanium alloy machining with polycrystalline diamond tool under different lubricating modes
The present work deals with the investigation on machining of difficult-to-machine material titanium alloy (Ti-6Al-4V) using poly crystalline diamond (PCD) tool under different coolant strategies, namely dry, flooded and MQL. Taguchi technique has been employed and the optimization results indicated that MQL lubricating mode with cutting speed of 150 m/min,
Mat. Res.. Publicado em: 15/08/2014
-
36. Residual stress analysis of drive shafts after induction hardening
Typically, for automotive shafts, shape distortion manifests itself in most cases after the induction hardening by an effect known as bending. The distortion results in a boost of costs, especially due to machining parts in the hardened state to fabricate its final tolerances. In the present study, residual stress measurements were carried out on automotive
Mat. Res.. Publicado em: 03/06/2014