Machining
Mostrando 13-24 de 254 artigos, teses e dissertações.
-
13. Análise da rugosidade superficial de barras de aço SAE 1045 após torneamento
RESUMO Neste trabalho foram investigadas as influências de alguns dos principais fatores do torneamento sobre o acabamento da superfície e a rugosidade de uma peça torneada. Foram analisadas barras de aço SAE 1045 torneadas em um torno controle numérico computadorizado (CNC), com auxílio da técnica de Planejamento de experimentos (DOE) para formar tri
Matéria (Rio J.). Publicado em: 20/05/2019
-
14. Investigation of Austenitic Stainless Steel Coatings on Mild Steel Produced by Friction Surfacing Using a Conventional CNC Machining Center
The friction surfacing process allows deposition of similar and dissimilar coatings in the solid state, avoiding some of the problems associated with conventional coating methods in which fusion is involved. In the present work, a viability assessment of producing AISI 304 austenitic stainless steel coatings on AISI 1020 low-carbon steel substrates using a m
Mat. Res.. Publicado em: 21/01/2019
-
15. Synthetic granite composite for precision equipment structures
ABSTRACT The structure is a component that plays an extremely important role in the equipment’s performance, it must withstand efforts without compromising the function, receive and transfer heat, dampen vibrations and position the elements, as well as promote ergonomics and aesthetics. In lightweight and precision equipment’s the raw material used must
Matéria (Rio J.). Publicado em: 06/12/2018
-
16. Surface Integrity Analisys in the Hard Turning of Cemented Steel AISI 4317
This work was based on the surface integrity analysis of hardened steel, AISI 4317 case carburized, quenched and tempered with 58 HRC, obtained by a turning operation executed with CBN (cubic boron nitride) tool, varying three basic cutting parameters (cutting speed, feed rate and cutting depth). The surface integrity characterization was conducted analyzing
Mat. Res.. Publicado em: 26/07/2018
-
17. Estudio de los parámetros de proceso del anodizado por plasma químico en Ti-6Al-4V ELI para implantes dentales
ABSTRACT In order to study the variation effect of some parameters of micro-arc oxidation process (MAO) on Ti-6Al-4V samples for dental implants, several treatments were carried out under different conditions of current density, exposure time and electrolyte chemical composition. These processes resulted in generated bioactive titanium oxide surface coatings
Matéria (Rio J.). Publicado em: 19/07/2018
-
18. Estudio del comportamiento de fundición CADI sometida a FCR
ABSTRACT Ductile Iron (DI) is a development of the iron alloys introduced in the ´50s, with free graphite in the form of nodules. Austempered Ductile Iron (ADI) is a development of DI later introduced, consisting on austempering heat treatment in order to obtain a high strength and high toughness material. Carbidic Austempered Ductile Iron (CADI) is a more
Matéria (Rio J.). Publicado em: 19/07/2018
-
19. Espuma ultraliviana de Mg a partir de viruta reciclada
ABSTRACT Hundreds of people worldwide die or are severely maimed in collisions during traffic accidents, due to the energy transmitted to the passengers on impact. A dissipation of said energy is necessary to minimize it's effects, which can be achieved through absorbers. In recent years, metallic foams have started to be considered as energy absorbers. Meta
Matéria (Rio J.). Publicado em: 19/07/2018
-
20. Evaluation of the oil flow using the MQL technique applied in the cylindrical plunge grinding of AISI 4340 steel with cbn grinding wheel
Abstract The grinding process is defined as an abrasive cutting action of a tool known as grinding wheel, which is submitted to high rotations, promoting excellent finishing and accuracy in dimensions, respecting the parameters established in each project. During the machining, the cutting edges of the abrasive grains undergo wearing and this increases the c
REM, Int. Eng. J.. Publicado em: 2018-07
-
21. Influence of water in the MQL technique in the grinding of steel AISI 4340 using CBN wheels
Abstract Usually, machining employs cooling methods to avoid high temperatures. In most cases, the cutting fluid is applied with high flow and low pressures. This technique consumes a large amount of cutting fluid that causes serious problems in the environment and in the health of the worker. An alternative to the conventional cooling method is the Minimum
REM, Int. Eng. J.. Publicado em: 2018-07
-
22. Application viability evaluation of the Minimum Quantity Lubrication coolant technique under different flow rates in Plunge Cylindrical Grinding of the ABNT 4340 steel with aluminum oxide wheel
Abstract The coolant delivery technique known as Minimal Quantity Lubrication (MQL) has been employed in machining since the end of the 20th Century and has gained considerable evidence in the last years as a viable alternative to the use of the conventional coolant technique (flood). Due to the low oil flow rate delivered by the MQL technique in grinding op
REM, Int. Eng. J.. Publicado em: 2017-12
-
23. Study of the AISI 52100 Steel Reuse Through the Powder Metallurgy Route Using High Energy Ball Milling
The AISI 52100 is a tool steel used in industry to produce bearings. After the end of its life cycle, it is remelted or discarded in deposits. The powder metallurgy rises as an alternative to recycle this material without any waste. The steps used to produce the AISI 52100 steel by powder metallurgy included: Machining with speed of 45 rpm, high energy ball
Mat. Res.. Publicado em: 06/11/2017
-
24. Residual Stresses Analysis in Ball end Milling of Nickel-Based Superalloy Inconel 718
Inconel 718 is widely used in the aviation, space, automotive and biomedical industries because of its outstanding properties. Near-surface residual stresses that are induced by ball end milling in Inconel 718 can be crucial for the performance and service time of the machined parts. In this paper, the influences of cutting conditions, including the use of c
Mat. Res.. Publicado em: 18/09/2017