Air Cooling
Mostrando 1-12 de 156 artigos, teses e dissertações.
-
1. EFFECT OF THE MIST MICRO-SPRAY TIME ON PHOTOSYNTHETIC SPATIAL HETEROGENEITY OF GRAPE CANOPY
ABSTRACT In grape, high temperatures and low humidity prolong midday depression of foliar photosynthesis and dramatically reduce fruit yield. In this study, we explored the effects of various mist micro-spray treatments on grape photosynthesis at a test site in Shanshan County (N, 42.91°; E, 90.30°), Turpan, Xinjiang, China. We tested four different mist m
Eng. Agríc.. Publicado em: 2021-02
-
2. Behavior of the effective heat transfer coefficient and global thermal resistance in freezing of fruit juice model solutions in cylindrical packages
Abstract In this study the effect of packing on freezing time, effective heat transfer coefficient and global thermal resistance were evaluated during the freezing of fruit juice model solution in an air blast freezer. Two configurations were arranged with 40 buckets and 15 kg of solution in each, totaling 600 kg. Thermocouples were installed to monitor the
Food Sci. Technol. Publicado em: 2020-12
-
3. 3D numerical investigation of mixture formation and combustion in a DISI engine at part-load under stratified operation
This work investigates through numerical simulation, the operation of a big bore direct fuel injection spark ignition engine, at part load under stratified operation. It evaluates fuel-air mixture preparation and combustion process with the adoption of detailed chemical kinetics mechanisms for both Isooctane and Ethanol, and applying adaptive mesh refinement
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 2020
-
4. Efeito de dois sistemas de resfriamento sobre os hormônios tireoidianos e as variáveis termofisiológicas de matrizes suínas em lactação
RESUMO Avaliaram-se os efeitos do sistema de resfriamento evaporativo com pressão negativa (SRE) e aspersão de água sobre o telhado (AAT), as variáveis termofisiológicas, os hormônios tireoidianos e a relação neutrófilo:linfócito (N:L) em porcas. Utilizaram-se 61 fêmeas em lactação, que foram divididas nos dois ambientes térmicos, sendo 30 em S
Arq. Bras. Med. Vet. Zootec.. Publicado em: 13/12/2019
-
5. Evaluation of the Heat and Energy Performance of a Datacenter Using a New Efficiency Index: Energy Usage Effectiveness Design – EUED.
Abstract Data Centers are growing steadily worldwide, and they are expected to continue growing up to 53% in 2020. Energy efficiency, in high power consumption, is a key venue. There are methodologies to measure this efficiency, one example is using the PUE (Power Usage Effectiveness) index. In this paper is proposed a new index for measuring efficiency at
Braz. arch. biol. technol.. Publicado em: 25/11/2019
-
6. Desempenho e termorregulação de porcas lactantes alojadas em diferentes localizações no interior de um galpão com sistema de resfriamento evaporativo em ambiente tropical
ABSTRACT The effects of housing lactating sows at different locations in a shed with evaporative cooling system (ECS) on their thermoregulation and reproductive and productive performance of the sow and the litter in summer were determined. 34 females were used in the three lines of cages at these locations: near the pad cooling; in the middle of the shed an
Arq. Bras. Med. Vet. Zootec.. Publicado em: 28/10/2019
-
7. Avaliação energética de um edifício de serviços: Escola Superior Aveiro Norte, Portugal
Resumo O objetivo deste trabalho é realizar uma avaliação energética da Escola Superior Aveiro Norte (ESAN), situada no município de Oliveira de Azeméis (Portugal). Esse edifício possui tecnologias de climatização pouco convencionais em Portugal, como bombas de calor geotérmicas associadas a piso radiante e ventilação, com pré-aquecimento de ar,
Ambient. constr.. Publicado em: 03/10/2019
-
8. Atomization Characteristics of Droplet and Morphologies of Arc Sprayed Ni-Al Particles and Composition Coatings
Droplet atomization characteristics and its morphology in twin-wire arc sprayed (TWAS) Ni-Al were explored in depth. Both numerical model and theoretical method were built for calculating the process of the droplet deformation and breakup in air flow, which based on the standard k-ε model and the volume of fluid (VOF) dual-phase flow model. The atomization
Mat. Res.. Publicado em: 23/09/2019
-
9. Aplicação da técnica de CAMQL na retificação cilíndrica externa do aço AISI 4340 utilizando rebolo de CBN
RESUMO O processo de retificação possui como características o bom acabamento superficial e alta precisão dimensional e geométrica. Assim, peças usinadas por este processo possuem um alto valor agregado por se tratar de um processo de acabamento que é comumente realizado nas últimas etapas da fabricação. Um fator limitador do processo de retificaç
Matéria (Rio J.). Publicado em: 16/09/2019
-
10. Escritórios de planta livre: o impacto de diferentes soluções de fachada na eficiência energética
Resumo No Brasil, os edifícios de escritórios de planta livre têm se destacado pela utilização de fachadas totalmente envidraçadas, aspecto que pode impactar diretamente o consumo de energia do ar condicionado. O objetivo deste estudo é classificar e caracterizar o desempenho energético de edifícios de escritório de planta livre em três climas bra
Ambient. constr.. Publicado em: 10/06/2019
-
11. Tri-modal Microstructure in Different Loading Zones Under TA15 Ti-alloy Isothermal Local Conventional Forging and Given Subsequent Heat Treatment
For TA15 Ti-alloy large-scale component, isothermal local conventional forging (ILCF) combined with subsequent heat treatment provides a feasible approach to obtain a tri-modal microstructure with attractive comprehensive performance. However the tri-modal microstructure characteristics and evolution laws in the first and second loading zones are lack of und
Mat. Res.. Publicado em: 10/06/2019
-
12. Heat Treatment of Sintered Valve Seat Inserts
The characterization of sintered valve seat inserts (VSIs) after being subjected to different heat treatment operations has been carried out. The VSIs were obtained from three different alloys by mixing iron powder with AISI M3:2, AISI M2 high-speed steels, and AISI D2 tool steel. After sintering, the VSI were quenched in air followed by double tempering at
Mat. Res.. Publicado em: 02/08/2018