Tungsten Carbide
Mostrando 1-12 de 32 artigos, teses e dissertações.
-
1. Efeitos do Processo de Refusão a Laser na Microestrutura e No Comportamento de Desgaste do Revestimento de WC Aspergido com HVOF
RESUMO O desgaste de componentes e equipamentos industriais e agrícolas representa um grande fator de depreciação de capital e de fonte de despesas com manutenção e reposição de componentes mecânicos. Como o desgaste é um fenômeno essencialmente superficial, envolvendo a remoção mecânica indesejável de material de superfícies, a solução estu
Matéria (Rio J.). Publicado em: 25/11/2019
-
2. Integrated Experimental Approach for Alloying of Surface Layer Ti6Al4V+B4C Metal Matrix Composites using Laser Treatment
Surface engineering applications have brought the titanium and its alloys into the limelight in the manufacturing industries such as the aerospace, automobile, marine, chemical processing industry, nuclear power and biomedical. Despite the growths experienced in the use of this material, it is plagued with poor wear behaviour, especially when in contact with
Mat. Res.. Publicado em: 17/01/2019
-
3. First evaluation of semidirect recycling methods for the reclamation of cemented carbides based on a literature survey
ABSTRACT At the moment the industrially applied techniques for cemented carbide reclamation feature several deficiencies. Depending on the process route, obstacles consist in high energy and chemical consumption (indirect recycling methods) or a deterioration of the recycled product in comparison with the primary material (direct recycling approach). Therefo
Matéria (Rio J.). Publicado em: 19/07/2018
-
4. Activity and Stability of Dispersed Multi Metallic Pt-based Catalysts for CO Tolerance in Proton Exchange Membrane Fuel Cell Anodes
ABSTRACT Studies aiming at improving the activity and stability of dispersed W and Mo containing Pt catalysts for the CO tolerance in proton exchange membrane fuel cell (PEMFC) anodes are revised for the following catalyst systems: (1) a carbon supported PtMo electrocatalyst submitted to heat treatments; (2) Pt and PtMo nanoparticles deposited on carbon-supp
An. Acad. Bras. Ciênc.. Publicado em: 16/04/2018
-
5. The correlation between tribological properties of nanostructure TiN coatings and deposition process parameters in PACVD system
ABSTRACT Titanium base coatings are being used extensively for improving wear characteristics at the surface of different parts. Titanium nitride was deposited by Plasma Assisted Chemical Vapor Deposition (PACVD) techniques with purpose improve interface with substrate, as this can increase wearing of the entire part in spite of desirable wear behavior of Ti
Matéria (Rio J.). Publicado em: 22/06/2017
-
6. Influence of Tungsten on Dry Sliding Wear Behaviour of Sintered/Hot Extruded P/M Alloy Steels (Fe-C-W-Ti)
In the present scenario, Powder Metallurgy (P/M) is an established manufacturing process used to make components of complex geometries with high strength and tolerances by using incredible materials which are difficult to melt or form by other processes. The mechanical properties and microstructures will determine the component characteristic dependent on th
Mat. Res.. Publicado em: 08/06/2017
-
7. Influence of Boriding Process in Adhesion of CVD Diamond Films on Tungsten Carbide Substrates
AbstractThis paper shows successful hindering of the negative effects of the cobalt binder in the process of coating WC-Co cutting tools with CVD diamond films. The strategy was creating a boron-rich layer on the surface of the WC-Co substrates as an interlayer to block Co migration. The traditional boriding technique was improved by preheating the salt powd
Mat. Res.. Publicado em: 2015-10
-
8. Modelling and optimization of the surface roughness in the dry turning of the cold rolled alloyed steel using regression analysis
Surface quality of the machined parts is one of the most important product quality indicators and one of the most frequent customer requirements. The average surface roughness (Ra) represents a measure of the surface quality, and it is mostly influenced by the following cutting parameters: the cutting speed, the feed rate, and the depth of cut. Quantifying t
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2012-03
-
9. Aspects on the optimization of die-sinking EDM of tungsten carbide-cobalt
At present, due to their properties, the tungsten carbide-cobalt (WC-Co) composite materials are in huge demand by industry to manufacture special tools, dies/molds and components under erosion. The powder metallurgy is the usual process applied to obtain WC-Co products, but in some cases this process is unable to produce tools of very complex shapes and hig
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2010-12
-
10. Comparison of finishing and polishing systems for residual resin removal after debonding
OBJECTIVE : The aim of this study was to evaluate (1) the effectiveness of one-step polishers on the surface morphology of enamel using scanning electron microscope (SEM) and compare their effects with conventional systems for residual adhesive removal; and (2) the time spent to remove resin remnants. MATERIAL AND METHODS: Metal brackets were bonded to the b
Journal of Applied Oral Science. Publicado em: 2009-06
-
11. Single point diamond turning of the tungsten carbide / Usinabilidade do carbeto de tungstênio no torneamento com ferramenta de diamante
The single point diamond turning of the Tungsten Carbide is presented. The motivation for this study is the material´s high hardness and potential application for micromolds. A Tungsten Carbide sample was subjected to tests for determination of cutting parameters to achieve the ductile regime of material removal. Based on experimental results it was conclud
Publicado em: 2009
-
12. Nanolitografia do silício utilizando o microscópio de força atômica / Silicon nanolithography using a atomic force microscope
The semiconductor industry is increasingly interested in the miniaturization of devices in the nanometer range. As the traditional techniques of lithography are reaching their limits growth the demand for new, including those that use equipment operating by probe, such as the atomic force microscope (AFM). One of the techniques that uses AFM on to produce na
Publicado em: 2009