Surface Polishing
Mostrando 1-12 de 95 artigos, teses e dissertações.
-
1. Morphological and Structural Variations in Anodic Films grown on Polished and Electropolished Titanium Substrates
The objective of this work was to investigate the effects of anodization parameters on the anatase phase formation of titanium oxide films, which have been grown on both electropolished and non-electropolished titanium surfaces by direct current anodization in 0.25 and 2.5 mol L-1 H3PO4 solutions, respectively, at three anodization times (3, 6 and 12 hours).
Mat. Res.. Publicado em: 11/11/2019
-
2. Effect of immersion in various disinfectant solutions on the properties of a heat-cured acrylic resin
RESUMO Objetivo: Avaliar a influência da imersão em diferentes soluções desinfetantes na microdureza e rugosidade de uma resina acrílica de termoativação. Métodos: Corpos de prova de resina acrílica termopolimerizável foram imersos em água destilada, vinagre comercial de uso doméstico, hipoclorito de sódio e peróxido de hidrogênio, por perí
RGO, Rev. Gaúch. Odontol.. Publicado em: 28/10/2019
-
3. Electrolytic polishing of compacted graphite iron for revealing subsurface graphite of honed cylinders
ABSTRACT The superficial characteristics of honed surfaces are relevant for the tribological performance of cylinders of internal combustion engines (MCI). Recent studies found a correlation between the occurrence of the phenomenon called folded metal and the presence of graphite of cast irons. However, the honing process tends to overlap the graphite, such
Matéria (Rio J.). Publicado em: 20/05/2019
-
4. Surface morphologic evaluation of orthodontic bonding systems under conditions of cariogenic challenge
Abstract: Orthodontic bonding systems are submitted to demineralization and remineralization dynamics that might compromise their surface smoothness, and favor biofilm aggregation and caries development. The aim of the present study was to evaluate the effects of a cariogenic challenge model (in vitro pH-cycling model) on the surface roughness and topography
Braz. oral res.. Publicado em: 25/04/2019
-
5. Surface Topography, Gloss and Flexural Strength of Pressable Ceramic After Finishing-Polishing Protocols
Resumo O objetivo deste estudo foi avaliar o efeito de diferentes protocolos de acabamento e polimento na rugosidade da superfície, brilho, resistência à flexão biaxial e morfologia de cerâmica prensada. Trinta discos de cerâmica (12x1 mm) foram produzidos e divididos em cinco grupos (n=6): CT- controle (glaze); DA- ponta diamantada de granulação fin
Braz. Dent. J.. Publicado em: 04/04/2019
-
6. Avaliação do manchamento e da rugosidade superficial de materiais restauradores diretos após diferentes sistemas de polimento: estudo in vitro
Resumo Introdução Com o avanço estético e tecnológico dos compósitos restauradores diretos, a procura pela Odontologia Éstética tem aumentado. Objetivo Avaliar o manchamento e a rugosidade superficial dos compósitos Filtek Z350 (3M ESPE) e Filtek Bulk Fill (3M ESPE), polidos por diferentes sistemas: Disco SofLex e Disco SofLex diamantado espiral
Rev. odontol. UNESP. Publicado em: 11/03/2019
-
7. Influence of ethanol-wet dentin, adhesive mode of application, and aging on bond strength of universal adhesive
Abstract The aim of this study was to evaluate the effect of ethanol on the bond longevity of a universal adhesive system to bovine dentin, under different modes of adhesive application and artificial aging. Bovine dentin was exposed, and the smear layer was standardized by sandpaper polishing. Specimens were randomly divided into 2 groups: ethanol (E) and n
Braz. oral res.. Publicado em: 11/10/2018
-
8. Recubrimientos porosos de dióxido de titanio sintetizados por oxidación anódica
ABSTRACT Titanium dioxide is one of the most used materials in heterogeneous photocatalysis due to its commercial availability, low cost, chemical stability, low toxicity and high photocatalytic activity. One of the most efficient and economical methods to obtain TiO2 coatings is the plasma electrolytic oxidation. In this anodization process, a direct curren
Matéria (Rio J.). Publicado em: 19/07/2018
-
9. Surface Characterization of NiTi Superelastic and Shape Memory Alloys After Electrolytic Polishing
For the biomedical application of NiTi alloys, an excellent surface finishing process is required to guarantee high corrosion resistance and biocompatibility, eliminating the allergenic and toxic effects associated with the release of nickel ions in the body. Electropolishing is a process that can reduce surface imperfections and form a thin protective layer
Mat. Res.. Publicado em: 09/11/2017
-
10. Surface Modification of Ti6Al4V Alloy by Pulsed Lasers: Microstructure and Hydrophobic Behavior
In many aerospace applications, it is important to produce hydro-repellent surfaces because water and ice accumulation could lead to malfunctioning of the part or component with a potential critical failure. In this study, it was investigated the texturing of a titanium alloy (Ti6Al4V) by applying a pulsed Nd:YAG laser, aimed at the surface characterization
Mat. Res.. Publicado em: 21/09/2017
-
11. Determination of Chlorophenol in Environmental Samples Using a Voltammetric Biosensor Based on Hybrid Nanocomposite
In this work, a simple electrochemical biosensor for 4-chlorophenol was developed based on laccase immobilized on a hybrid nanocomposite (ZnO nanoparticles/chitosan), and incorporated in a carbon paste electrode. There are few biosensors in the literature for this specific pollutant because it tends to form polymeric films on the electrode, causing surface p
J. Braz. Chem. Soc.. Publicado em: 2017-07
-
12. Microstructural Characterization and Influence of Ceramography Method on the Microhardness of Sintering Agents Added Silicon Carbide
This study carried out the microstructural characterization, by light microscopy, of sintered SiC in the presence of liquid phase at temperatures of 1800, 1850 and 1900 ºC, added with Al2O3 and Y2O3 as well with Al2O3-YAG composite in the proportions of 5, 10 and 15% by weight. It was possible to observe the formation of microstructural patterns resulting f
Mat. Res.. Publicado em: 15/05/2017