Strain And Stresses
Mostrando 13-24 de 187 artigos, teses e dissertações.
-
13. Analytical Strain-softening Solutions of a spherical cavity
ABSTRACT This paper deals with a spherical cavity excavated in infinite homogeneous and isotropic strain-softening rock mass subjected to a hydrostatic initial stresses. By simplifying the strain-softening process of the post-failure region as a Multi-step Brittle-Plastic model (MBPM), analytical solutions of the spherical cavity are derived with the consid
Lat. Am. j. solids struct.. Publicado em: 16/05/2018
-
14. Free vibration analysis and design optimization of SMA/Graphite/Epoxy composite shells in thermal environments
Abstract Composite shells, which are being widely used in engineering applications, are often under thermal loads. Thermal loads usually bring thermal stresses in the structure which can significantly affect its static and dynamic behaviors. One of the possible solutions for this matter is embedding Shape Memory Alloy (SMA) wires into the structure. In the
Lat. Am. j. solids struct.. Publicado em: 23/04/2018
-
15. Monitoring structures with optical fibers: infiltration detection
ABSTRACT The use of sensors and optical fibers for monitoring structures is continuously growing. Strains, displacements, accelerations, temperatures are just a few of the monitoring possibilities. In the case of dam structures, concrete face rockfill dams constitute a type of structures where the monitoring of water infiltrations is of particular interest.
An. Acad. Bras. Ciênc.. Publicado em: 2018-04
-
16. The Wire Drawing Mechanics of Near-Equiatomic NiTi SMA
The wire drawing mechanic of Ti-49.82Ni (at. %) Shape Memory Alloy (SMA) was investigated through the true stress-strain curves and drawing stresses. The tensile tested solution treated wire presented a four steps elongation at temperatures below the austenite finish temperature (AF), and a conventional one-step behavior above the martensite deformation temp
Mat. Res.. Publicado em: 26/03/2018
-
17. Growth Stress in Peltophorum dubium and its Correlation with the Growth Variables
ABSTRACT The exploitation of valuable native timber species in forest restoration projects has emerged as a promising strategy to make restoration financially viable. There are few studies regarding the quality of timber from restoration plantations. The aim of this study was to analyze growth stresses by determining the longitudinal residual strain (LRS) a
Floresta Ambient.. Publicado em: 19/03/2018
-
18. Impact Damage Analysis with Stress Continuity Constraints Fulfilment at Damaged-Undamaged Regions and at Layer Interfaces
Abstract Low-velocity impacts have a relevant importance for safety of laminated and sandwich composite structures, because they are highly susceptible to damage. In this paper, a 3D cost effective zig-zag model is developed in order to efficiently simulate such impacts. It a priori fulfills the continuity of out-of-plane stresses at layer interfaces, the co
Lat. Am. j. solids struct.. Publicado em: 2017-08
-
19. Heterologous expression of a rice metallothionein isoform (OsMTI-1b) in Saccharomyces cerevisiae enhances cadmium, hydrogen peroxide and ethanol tolerance
Abstract Metallothioneins are a superfamily of low-molecular-weight, cysteine (Cys)-rich proteins that are believed to play important roles in protection against metal toxicity and oxidative stress. The main purpose of this study was to investigate the effect of heterologous expression of a rice metallothionein isoform (OsMTI-1b) on the tolerance of Saccharo
Braz. J. Microbiol.. Publicado em: 2017-07
-
20. Analysis of Thermo-Mechanical Stress in Fiber Bragg Grating Used for Hydro-Generator Rotor Temperature Monitoring
Abstract Fiber Bragg gratings (FBGs) offer new possibilities to monitor accurately the rotor temperature. Dozens of sensors can be mounted in series in a single fiber and used to measure the temperature in several points of the rotor winding. Such sensors installed directly on the rotor winding surface are thermally isolated from the cooling air by a silicon
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 2017-04
-
21. Softening Mechanisms of the AISI 410 Martensitic Stainless Steel Under Hot Torsion Simulation
This study investigated the softening mechanisms of the AISI 410 martensitic stainless steel during torsion simulation under isothermal continuous in the temperature range of 900 to 1150 °C and strain rates of 0.1 to 5.0s-1. In the first part of the curves, before the peak, the results show that the critical (εc) and peak (εp) strains are elevated for hig
Mat. Res.. Publicado em: 23/01/2017
-
22. Factors Affecting Kinetics of Strain Aging in S275JRC Steel
The materials parameter i.e. microstructure as well as the processing factors i.e. aging time and temperature, the amount of plastic deformation, and residual stresses affecting the kinetic of strain ageing in the S275JRC steel were investigated in detail. For this purpose, 5 % pre-strained steel was aged at 160ºC for different intervals. The ageing behavio
Mat. Res.. Publicado em: 19/12/2016
-
23. Development and Test of an Equipment to Measure Residual Strain Inside Pipes Using the Hole-Drilling Method
Abstract Residual stresses are present in materials or structural component in the absence of external loads or changes in temperatures. The most common causes of residual stresses being present are the manufacturing or assembling processes. All manufacturing processes, such as casting, welding, machining, moulding, heat treatment, etc, introduces residual s
Lat. Am. j. solids struct.. Publicado em: 2016-12
-
24. On Micro-Buckling of Unidirectional Fiber-Reinforced Composites by Means of Computational Micromechanics
Abstract Micro-buckling of unidirectional fiber-reinforced composites is investigated in this paper by means of an explicit representation of a geometrically imperfect fiber within the context of kinematical and material non-linear behavior. Two types of fiber imperfections are considered: a helicoidal shape, identified as 3D imperfection; and a sinusoidal p
Lat. Am. j. solids struct.. Publicado em: 2016-12