Steel Metallurgy
Mostrando 1-12 de 37 artigos, teses e dissertações.
-
1. Obtainment of a new metal matrix composite from the recycling of UNS S31803 duplex stainless steel by powder metallurgy
Abstract The purpose of circular economy is to maximize resources efficiency. With the increase in consumption of raw materials, energy and waste generation, recycling is necessary for environmental and industrial reasons. Thus, the powder metallurgy, together with mechanical milling, stands as a new method for scraps recycling. This study aimed to produce U
REM - International Engineering Journal. Publicado em: 2022
-
2. Study on Effect of EAFD Particulate Reinforcement in AA7075 Aluminum Matrix Composites
Eletric arc furnace dust is dangerous solid waste that is generated in steel manufacturing processes. The utilization of the dust from these industries avoids disposing it into industrial waste landfills and saves costs. In this study, an attempt has been made to fabricate aluminum matrix composites reinforced with EAFD particulate, throught the conventional
Mat. Res.. Publicado em: 13/09/2018
-
3. Study of the AISI 52100 Steel Reuse Through the Powder Metallurgy Route Using High Energy Ball Milling
The AISI 52100 is a tool steel used in industry to produce bearings. After the end of its life cycle, it is remelted or discarded in deposits. The powder metallurgy rises as an alternative to recycle this material without any waste. The steps used to produce the AISI 52100 steel by powder metallurgy included: Machining with speed of 45 rpm, high energy ball
Mat. Res.. Publicado em: 06/11/2017
-
4. Effect of Boride Layer on PM HSS AISI M2 on the Mechanisms Acting in the Transverse Rupture Strength Test
Herein, it was conducted a study in order to examine the main fracture characteristics in the transverse rupture strength test (TRS) of a high speed steel (HSS) AISI M2 produced by powder metallurgy (PM) and with boriding treatment. Four conditions have been studied: as-sintered, borided, normalized and borided + TiN. The TRS tests were conducted in accordan
Mat. Res.. Publicado em: 06/11/2017
-
5. Structural and Magnetic Properties of Duplex Stainless steel (UNS S31803) Powders Obtained by high Energy Milling of Chips with Additions of NbC
In this study, the high energy mechanical milling was utilized to the production of duplex stainless steel powders from the recycling chips with and without the addition niobium carbide. The effect of milling time and addition carbide on the morphology, particle size and magnetic properties of the powders was investigated. The utilization of the powder metal
Mat. Res.. Publicado em: 30/10/2017
-
6. Effect of Processing Route on the Microstructure and Mechanical Properties of Hot Work Tool Steel
Powder metallurgy is a growing sector in industrial production, as it offers outstanding energy, cost and material savings in comparison with established processing routes such as casting. Hot work toll steels are usually produced by ingot metallurgy, but also by powder metallurgy, namely hot isostatic pressing and powder forging routes. In this paper we inv
Mat. Res.. Publicado em: 21/08/2017
-
7. Influence of Tungsten on Dry Sliding Wear Behaviour of Sintered/Hot Extruded P/M Alloy Steels (Fe-C-W-Ti)
In the present scenario, Powder Metallurgy (P/M) is an established manufacturing process used to make components of complex geometries with high strength and tolerances by using incredible materials which are difficult to melt or form by other processes. The mechanical properties and microstructures will determine the component characteristic dependent on th
Mat. Res.. Publicado em: 08/06/2017
-
8. Investigation of borided layers contribution on the wear resistance and adhesion of TiN coatings
ABSTRACT The purpose of the investigation was to examine the possibility of improving tool life by reducing the wear effect and improving the adhesion of a thin film through a compound configuration that consists in boriding and PVD deposition. Single layer coatings of TiN were deposited by PVD (cathodic arc) on quenched and tempered and on borided powder me
Matéria (Rio J.). Publicado em: 02/05/2017
-
9. Evaluation of the milling efficiency increase of AISI 52100 steel using niobium carbide addition through high energy ball milling
The AISI 52100 is a tool-type steel and is more often used in industry for the production of bearings. After the end of its life cycle, it is discarded or remelted, but both processes are considered expensive. Thus, the possibility of reusing this material through the powder metallurgy (PM) route is considered advantageous, since it transforms a waste into a
Rem: Rev. Esc. Minas. Publicado em: 2015-09
-
10. Microstructural Transformations in Dissimilar Welds between Austenitic Stainless Steel and Ferritic Stainless Steel
This research studies the metallurgical transformations taking place the SMAW welding of AISI 316L austenitic stainless steel with AISI 430 ferritic stainless steel. To perform the study were used two different electrodes, AWS E309L austenitic and AWS E2209-16 duplex stainless steels 3.2 mm diameter. The joints were made with a single-pass welding including
Soldag. insp.. Publicado em: 2015-03
-
11. The effect of voltage on the arc stud welding of microwave sintered Fe+Al powder mixture
The joining of powder metallurgy products is of importance because of high demand in many industrial applications. In this study, the effect of welding voltage on the joint quality has been investigated using discharge arc stud welding, a low heat input welding method, without gas protection to join steel stubs to microwave sintered compacts containing a pow
Mat. Res.. Publicado em: 03/06/2014
-
12. Análise dos efeitos nos dividendos das empresas de capital aberto inscritas na BM&FBovespa, do segmento de siderurgia e metalurgia, após a promulgação da Lei n 11.638/07 / Analysis of effects on dividends from public companies listed on the BM&FBovespa, of the steel and metallurgy segment, after the enactment of Law 11.638/07
propósito desta pesquisa é analisar os efeitos das mudanças introduzidas na legislação contábil pela Lei n 11.638/07 nos dividendos pagos aos acionistas, por meio de um estudo no patrimônio líquido e lucro líquido. Para o desenvolvimento do trabalho tomou-se como base empresas do segmento de siderurgia e metalurgia com ações listadas na BM&FBovesp
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 07/12/2012