Simulation Of Grains
Mostrando 1-12 de 22 artigos, teses e dissertações.
-
1. Crecimiento de grano tridimensional con partículas móviles usando método de Monte Carlo
ABSTRACT In this paper we present a simulation model of grain growth with moving particles in three dimensions using the Monte Carlo method. The effect of concentration and particle size on grain size was studied. In general, it was possible to observe the migration of the particles towards the grain boundaries and the braking that they produce on the moveme
Matéria (Rio J.). Publicado em: 19/07/2018
-
2. Simulation of CP-Ti Recrystallization and Grain Growth by a Cellular Automata Algorithm: Simulated Versus Experimental Results
The application of cellular automata in materials science requires the conversion of the automata's rules and abstract general properties to rules and properties associated with the material and phenomena under study. In this paper we propose a model which uses cellular automata to simulate recrystallization and grain growth during isothermal and non-isother
Mat. Res.. Publicado em: 03/04/2017
-
3. Softening Mechanisms of the AISI 410 Martensitic Stainless Steel Under Hot Torsion Simulation
This study investigated the softening mechanisms of the AISI 410 martensitic stainless steel during torsion simulation under isothermal continuous in the temperature range of 900 to 1150 °C and strain rates of 0.1 to 5.0s-1. In the first part of the curves, before the peak, the results show that the critical (εc) and peak (εp) strains are elevated for hig
Mat. Res.. Publicado em: 23/01/2017
-
4. Dynamic Response and Microstructure Evolution of Oxygen-Free High-Conductivity Copper Liner in Explosively Formed Projectile
Abstract The dynamic response and microstructure evolution of oxygen-free high-conductivity copper in a shaped charge liner are investigated through microstructural examination of a soft-recovery EFP. Adiabatic shear bands and voids which is the failure original of copper EFP can be observed in the rear part of the projectile. Numerical simulation results il
Lat. Am. j. solids struct.. Publicado em: 2017
-
5. Ferrite Quantification Methodologies for Duplex Stainless Steel
ABSTRACT In order to quantify ferrite content, three techniques, XRD, ferritoscope and optical metallography, were applied to a duplex stainless steel UNS S31803 solution-treated for 30 min at 1,000, 1,100 and 1,200 °C, and then compared to equilibrium of phases predicted by ThermoCalc® simulation. As expected, the microstructure is composed only by austen
J. Aerosp. Technol. Manag.. Publicado em: 2016-09
-
6. Mechanical properties of grain in silos for simulation designs
ABSTRACT For the calculation of silos structures it has been used new methods and computational tools that require mechanical properties knowledge that are still unknown for most storable materials, especially grains. In this context, we aimed to determine the mechanical properties of rice and beans grains with moisture contents of 10, 12, and 14% by applyin
Eng. Agríc.. Publicado em: 2016-08
-
7. 3D finite element modeling of grains refinement for magnesium alloys by extrusion-shear and experimental verification
To explore the deformation mechanisms of a new composite extrusion including extrusion and successive shear subsequently which is shorten "ES", Three dimensional finite element modeling of grain refinements for magnesium alloys by ES process has been researched. The ES die have been designed and manufactured and installed to the horizontal extruder. Finite e
Mat. Res.. Publicado em: 28/07/2014
-
8. Extrusion-shear of AZ31 alloy billets with low temperature and high speed by using three-dimensional finite element modeling and experiments
A new kind of compound extrusion technology including direct extrusion and shears for AZ31 magnesium billets can cause plastic large deformations and high strain rates. A series of compressive tests have been done to obtain the stress-strain curves of AZ31 magnesium alloy. Three-dimensional (3D) thermo-mechanical coupled finite element modeling of forming ma
Mat. Res.. Publicado em: 28/07/2014
-
9. Inhomogeneous Poisson point process nucleation: comparison of analytical solution with cellular automata simulation
Microstructural evolution in three dimensions of nucleation and growth transformations is simulated by means of cellular automata (CA). In the simulation, nuclei are located in space according to a heterogeneous Poisson point processes. The simulation is compared with exact analytical solution recently obtained by Rios and Villa supposing that the intensity
Materials Research. Publicado em: 2009-06
-
10. Implementação da rotina de unfolding para determinação de distribuição de tamanho de grãos esféricos via distribuição de interceptos lineares e de área de seção
Na unfolding method of linear intercept distributions and secction área distribution was implemented for structures with spherical grains. Although the unfolding routine depends on the grain shape, structures with spheroidal grains can also be treated by this routine. Grains of non-spheroidal shape can be treated only as approximation. A software was develo
Publicado em: 2009
-
11. GRAINS SIMULATION ON GPU / SIMULAÇÃO DE GRÃOS EM GPU
A proposta deste trabalho é viabilizar e acelerar a simulação de um sistema de grãos implementado inteiramente na GPU, utilizando o Método dos Elementos Discretos (MED). O objetivo de implementar todo o sistema na GPU é evitar o custo de transferência de informações entre a placa gráfica e a CPU. O sistema proposto simula partículas de diferentes
Publicado em: 2009
-
12. Tratamento de esgoto sanitário em um reator de leito expandido em escala plena, operado com regiões anaeróbia e aeróbia sobrepostas / Treatment of sanitary wastewater in a full scale expanded bed reactor, operated with overlap anaerobic and aerobic regions
This present research had as main objective the evaluation of the performance of a full scale expanded bed reactor (159.0 M POT.3), operated under anaerobic and overlapping anaerobic-aerobic, treating sanitary wastewater. As specific objectives, it was evaluated using commercial sand to complement the bed of particles and distribution of material support alo
Publicado em: 2009