Powder Coatings
Mostrando 1-12 de 27 artigos, teses e dissertações.
-
1. Biomimetic Coating of Mechanochemically Synthesized Zirconium Titanate
A biomimetic method was used to promote bioactivity of ZrTiO4. Zirconium titanate was obtained by using a combination of techniques such as mechanical milling and heat treatment of zirconia and titania powders. The effect of milling time on the evolution of the ZrTiO4 phase formation was studied. Powders were uniaxially pressed followed by heat treatment for
Mat. Res.. Publicado em: 10/07/2019
-
2. Characterization of new selective coatings, made of granite and chrome, for solar collectors
ABSTRACT The depletion of fossil fuel reserves and climate change caused by atmospheric pollution has led the human being to seek alternatives that are less damaging to the environment. The concern and the awareness of the population open space for the study of renewable energies to be deepened, among them the best use of solar energy. The use of alternative
Matéria (Rio J.). Publicado em: 10/06/2019
-
3. Investigation on the Wear Properties of Ti/TiC/TiN Composite Coatings Prepared by Powder Cored Wires Through TIG Method at Nitrogen Atmosphere on Titanium Substrate
In this present study, Tungsten Inert Gas (TIG) welding and powder filled cored wires with nitrogen shielding gas were utilized to produce TiC and TiN surface composite coatings on the titanium (Ti) sheet substrate. The TIG procedure was done at same welding parameters for all of prepared samples. Phase analysis and microstructures were done by X-ray Diffrac
Mat. Res.. Publicado em: 15/04/2019
-
4. Laser Cladding of Fe-based Metallic Glass/MoS2 Self-lubricating Composites: Effect of Power and Scanning Speed
MoS2 powder has been used to form "self-lubricating" composite coatings, which are very useful to increase the lifetime of machines where liquid lubricants cannot be used. In this work, amorphous overspray powder of Fe60Cr8Nb8B24 (at%) alloy was mixed with 5wt.% MoS2 powder and it was used to produce single tracks on AISI 1020 steel substrates by laser cladd
Mat. Res.. Publicado em: 01/02/2018
-
5. The Effect of Electroless Bath Parameters and Heat Treatment on the Properties of Ni-P and Ni-P-Cu Composite Coatings
Ni-P-(Cu) composite coatings were applied on a St37 steel in an acidic bath of hypophosphite composite. The effect of the concentration of the Cu particles and pH of the solutionon the amount of Ni and P of the coatings, their morphology, and hardness of the coatings were explored. Some of the coated samples were also heat treated at 400ºC for 1 hour. The p
Mat. Res.. Publicado em: 08/01/2018
-
6. Metallic Glass Formation Upon Rapid Solidification of Fe60Cr8Nb8B24 (at%) Alloy through LASER Cladding and Remelting
Fe60Cr8Nb8B24 (at%) amorphous powder and ingot were submitted to LASER cladding and remelting process, respectively. Fe-based coatings were produced using different LASER processing parameters and characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and Vickers microhardness. All coatings obtained by LASER cladding (LC) and layers obt
Mat. Res.. Publicado em: 17/11/2017
-
7. Synthesis of Vanadium Interface for HFCVD Diamond Deposition on Steel Surface
Laser cladding of vanadium carbide powder developed an interlayer on AISI D6 steel as a diffusional barrier and to relief thermal residual stress. Laser cladding experiments varied resolution (DPI) and scanning speed (mm/s). CVD diamond deposition on this interface went on by HFCVD technique. The coatings were characterized by X-ray diffraction analysis (XRD
Mat. Res.. Publicado em: 06/07/2017
-
8. Investigation of borided layers contribution on the wear resistance and adhesion of TiN coatings
ABSTRACT The purpose of the investigation was to examine the possibility of improving tool life by reducing the wear effect and improving the adhesion of a thin film through a compound configuration that consists in boriding and PVD deposition. Single layer coatings of TiN were deposited by PVD (cathodic arc) on quenched and tempered and on borided powder me
Matéria (Rio J.). Publicado em: 02/05/2017
-
9. Films Deposited from Reactive Sputtering of Aluminum Acetylacetonate Under Low Energy Ion Bombardment
Films were deposited from aluminum acetylacetonate (Al(acac)3) using a methodology involving reactive sputtering and low energy ion bombardment. The plasma was generated by the application of radiofrequency power to the powder containing electrode and simultaneously, negative pulses were supplied to the electrode where the substrates were attached. It was in
Mat. Res.. Publicado em: 10/04/2017
-
10. Preparation and Properties of Epoxy Resin-Coated Micro-Sized Ferrosilicon Powder
Ferrosilicon powder surface coated with a dense epoxy resin membrane was prepared via coating precipitation methods using silane coupling agents as the modifier and epoxy resin as the coating agent. FTIR, FESEM, MPMS-XL, and TG-DSC were used to analyze the morphology, surface composition, magnetic property and thermostability of ferrosilicon powder before an
Mat. Res.. Publicado em: 07/07/2016
-
11. Damage Mechanisms in AISI 304 Borided Steel: Scratch and Daimler-Benz Adhesion Tests
In this study, damage mechanisms in the FeB/Fe2B coatings formed on the surface of AISI 304 steel are determined by adhesion tests. First, the boriding of the AISI 304 steel was carried out through the powder-pack method at 1223 K in the range from 2-10 h of exposure time. After treatment, Berkovich depth-sensing indentation test were conducted; the result s
Mat. Res.. Publicado em: 24/11/2015
-
12. Influence of the Addition of Montmorillonite in an Epoxy Powder Coating Applied on Carbon Steel
AbstractPolymer coatings have been used for the corrosion protection of metal surfaces acting as a physical barrier against several corroding media. In spite of the good efficiency of these coatings their resistance is limited due to the presence of localized defects which give place to localized corrosion. Aiming to improve the barrier properties of these c
Mat. Res.. Publicado em: 2015-10