Photoelastic Resin
Mostrando 1-12 de 20 artigos, teses e dissertações.
-
1. Relevance of Resin for Photoelasticity
The goal of this study is to test photoelastic resins for manufacturing models with teeth and/or implants under chewing load. Four commercial brands have been chosen: Araldite (Ciba Chemicals), Flexible GIV-Rigid GIV (Polipox) and PL2 (Measurements Group). Nine discs were manufactured, four of them from each of the photoelastic resin brands and five from dif
Mat. Res.. Publicado em: 20/01/2020
-
2. Investigation of the influence of design details on short implant biomechanics using colorimetric photoelastic analysis: a pilot study
Introduction : The clinical survival of a dental implant is directly related to its biomechanical behavior. Since short implants present lower bone/implant contact area, their design may be more critical to stress distribution to surrounding tissues. Photoelastic analysis is a biomechanical method that uses either simple qualitative results or complex calcul
Res. Biomed. Eng.. Publicado em: 27/11/2015
-
3. Photoelastic stress analysis in mandibular bone surrounding bar-clip overdenture implants
The aim of this in vitro study was to evaluate, using the photoelastic analysis method, the stress distribution in mandibular bone surrounding a bar-clip overdenture when 2 implant angulations were simulated. Two mandibular photoelastic models were manufactured, with 2 implants embedded in the interforaminal region: model 1 - PAPI, a photoelastic analysis mo
Braz. oral res.. Publicado em: 17/12/2013
-
4. Importance of a distal proximal contact on load transfer by implant-supported single adjacent crowns in posterior region of the mandible: a photoelastic study
OBJECTIVE: This study aimed to evaluate the importance of a distal proximal contact on the load transfer to the posterior region of the mandible by non-splinted adjacent implant-supported crowns using photoelastic stress analysis. MATERIAL AND METHODS: A rectangular model (68x30x15 mm) was made of polymethylmethacrylate resin to simulate half of the mand
J. Appl. Oral Sci.. Publicado em: 2013-09
-
5. Photoelastic evaluation of the effect of composite formulation on polymerization shrinkage stress
We compared polymerization stress in two commercial composites and three experimental composites made using camphorquinone (CQ) and/or phenylpropanedione (PPD) as photoinitiators. The internal surfaces of photoelastic resin discs with cylindrical cavities were roughened and treated with adhesive. Composites were divided into five groups: two commercial compo
Brazilian Oral Research. Publicado em: 2012-06
-
6. Avaliação in vitro da transmissão de carga oclusal em próteses sobre implantes em função da inclinação de implantes através de análise fotoelástica / In vitro evaluation of occlusal load transmission in prosthetic implant according to the inclination of implants by photoelastic analysis
The All-on-Four technique was conceived in order to decrease the length of the cantilever in the rehabilitation of edentulous patients with implant-supported prosthesis. However, still persist questions related to the biomechanical behavior of implants and the proper technique All-on-Four, since issues such as peri-implant bone loss and failure of the prosth
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 01/09/2011
-
7. Análise fotoelástica da tensão de contração da polimerização de compósitos resinosos sob influência de técnicas restauradoras / Photoelastic analysis of polymerization shrinkage stress of composites under the influence of restorative techniques
Polymerization shrinkage stress is an undesirable and inevitable characteristic of adhesive restorations. It is important to understand the stress distribution to improve the clinical effectiveness of resin composite restoration. Chapter 1: The aim was to evaluate the polymerization shrinkage stress and degree of conversion of a resin composite material subm
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 20/06/2011
-
8. Analise fotoelastica da distribuição de tensão em diferentes sistemas de overdentures sobre implantes osseointegrados / Photoelastic analysis of the distribution of stress in different systerms of overdentures on osseous-integrated implants
The aim of this study was to evaluate through photoelastic analysis, the distribution of generated stress around implants and adjacent bone tissue, using differents implant-retained overdentures designs. Over an edentulous human mandible, achieve from a human model, 2 or 4 micro-unit replications abutments were embedded (Master, Conexao - Sao Paulo - SP) set
Publicado em: 2009
-
9. A comparative biomechanical and photoelastic evaluation of different fixation techniques of sagital spit ramus osteotomy in mandibular advancement / Avaliação mecanica e fotoelastica de diferentes tecnicas de fixação interna rigida da osteotomia sagital em avanços mandibulares
The aim of this research was to evaluate the resistance and tension areas created after load incidence in four different fixation techniques used in the sagittal split ramus osteotomy (SSRO). For this research, a sample of 50 polyurethane hemimandibles replicas were submitted to linear load test, divided in 4 different fixation techniques for SSRO ( 3 linear
Publicado em: 2009
-
10. Analise fotoelastica e extensometrica das tensoes induzidas por estruturas de protese sobre implantes fabricadas pelas tecnicas monobloco, soldagem de borda e metodo CAD/CAM / Photoelastic and strain gauge analysis of tensions induced over implant superstructures manufactured through one-pierce technique., bolder soldering and CAD/CAM method, border soldering and one-piece technique
The lack of passivity of the implant supported prosthesis may lead to mechanical and biological disorders over the implants. By the photoelastic and strain gauge analysis, the purpose of this research was to evaluate the stress over the implants after tightening the prosthesis superstructure over five dental implants. A stainless steel matrix was manufacture
Publicado em: 2009
-
11. Analise fotoelastica da tensão de contração ocorrida na polimerização de compositos resinosos / Photoelastic analysis of polymerization shrinkage stress in resin composites
O objetivo deste trabalho foi comparar a tensão de contração de polimerização gerada por compósitos resinosos em diferentes tempos após a fotoativação, por meio de análise fotoelástica. Três compósitos experimentais com diferentes tipos de fotoiniciadores, e dois compósitos comerciais, sendo um à base de monômeros metacrilatos e o outro à ba
Publicado em: 2009
-
12. Effect of light-curing units and activation mode on polymerization shrinkage and shrinkage stress of composite resins
The aim of this study was to evaluate the polymerization shrinkage and shrinkage stress of composites polymerized with a LED and a quartz tungsten halogen (QTH) light sources. The LED was used in a conventional mode (CM) and the QTH was used in both conventional and pulse-delay modes (PD). The composite resins used were Z100, A110, SureFil and Bisfil 2B (che
Journal of Applied Oral Science. Publicado em: 2008-02