Metals Mechanical Properties
Mostrando 1-12 de 52 artigos, teses e dissertações.
-
1. Effect of Welding Heat Input on the Microstructure and Mechanical Properties of Dissimilar Friction Stir-Welded Copper/Brass Lap Joint
Dissimilar lap welded joints of copper and brass metals were fabricated by friction stir welding (FSW) method at various welding heat inputs. The effect of welding heat inputs on the microstructure and mechanical properties of overlap welded joints at at two different join configurations (i.e. Advancing side and Retreating side joint configurations) was inve
Mat. Res.. Publicado em: 26/08/2019
-
2. An Experimental Study of the Solidification Thermal Parameters Influence upon Microstructure and Mechanical Properties of Al-Si-Cu Alloys
Metals solidification involves the transformation of the molten metal back into the solid state. Solidification structures impact heavily on the final product's characteristics. The microstructure effects on metallic alloys properties have been highlighted in various studies and particularly the dendrite arm spacing influence upon the mechanical properties s
Mat. Res.. Publicado em: 18/06/2018
-
3. On the creep behavior of carbon/epoxy non-crimp fabric composites
The use of composites in structural applications requires the study of specific properties to ensure that these materials are safe and an excellent option to replace some metals, for example. In the present study, vacuum assisted resin transfer molding (VARTM) was used prior to obtain carbon/epoxy non-crimp fabric composites. Dynamic mechanical analysis and
Mat. Res.. Publicado em: 26/02/2018
-
4. Experimental study of the diffusion-controlled corrosion of copper in the bottom of a jet stirred reactor
Abstract Jet stirred tank reactors are usually preferred to mechanically stirred tank reactors in the case of high pressure stirred tank reactors in order to avoid the mechanical problems inherent with mechanically agitated reactors. Owing to the impact force exercised by the fluid jet on the tank bottom, the tank bottom is subjected to severe corrosion. The
Braz. J. Chem. Eng.. Publicado em: 2018-01
-
5. Recycling and Mechanical Characterization of Polymer Blends Present in Printers
More and more electronic devices are being produced and most of them are disposed of improperly. In addition, as they contain heavy metals and toxic substances in their composition, the environmental impact increases. This work aims to study the recycling of polymers present in e-waste through the mechanical characterization of polymer blends produced with t
Mat. Res.. Publicado em: 22/06/2017
-
6. Efecto de la Composición Química del Metal de Aporte y del Calor Aportado Sobre la Microestructura y las Propiedades Mecánicas de Juntas Soldadas de Aceros Inoxidables Dúplex
Abstract Duplex stainless steels are characterized by good weldability and mechanical properties; they also present a high resistance to general and localized corrosion. They are the main materials when welding pipes with high requirements in different industries, mainly oil and gas. These steels have a microstructure consisting of two phases: 50% austenite
Soldag. insp.. Publicado em: 2017-06
-
7. Influences of Growth Velocity and Fe Content on Microstructure, Microhardness and Tensile Properties of Directionally Solidified Al-1.9Mn-xFe Ternary Alloys
In this study, influences of growth velocity and composition (Fe content) on the microstructure (rod spacing) and mechanical properties (microhardness, ultimate tensile strength and fracture surface) of Al-Mn-Fe ternary alloys have been investigated. Al-1.9 Mn-xFe (x=0.5, 1.5 and 5 wt. %) were prepared using metals of 99.99% high purity in the vacuum atmosph
Mat. Res.. Publicado em: 11/05/2017
-
8. Mechanical and microstructural behavior evolution of non-ferrous metals by ECASD
ABSTRACT In this study, Equal-Channel Angular Sheet Drawing- ECASD with a die set at 135° was used to produce plastic deformation onto an aluminum alloy AA-1100-O and a magnesium alloy AZ31-O samples, expecting a decreasing the grain size in order to increase the plasticity of these alloys under certain specific working conditions. In this study, the micros
Matéria (Rio J.). Publicado em: 02/05/2017
-
9. Predicting Secondary-Dendrite Arm Spacing of the Al-4.5wt%Cu Alloy During Unidirectional Solidification
Mechanical properties and performance of metallic materials depend on their microstructures. In order to develop engineering materials that match prescribed criteria and to enable design with multifunctional materials, it is essential to be able to predict their microstructural patterns, such as size, shape, and spacing of the dendritic structures observed i
Mat. Res.. Publicado em: 24/11/2016
-
10. Effect of Metal Acetylacetonates on the Photooxidative Destruction of High Density Polyethylene
The process of photooxidative destruction of high density polyethylene films containing different organic complexes of polyvalent metals as pro-oxidant additives after UV- irradiation was studied. During exposure to UV- irradiation, the more significant changes in the mechanical and thermal properties were detected for the foils containing pro-oxidant additi
Mat. Res.. Publicado em: 14/07/2016
-
11. Effect of Continuous and Pulsed Current on the Metallurgical and Mechanical Properties of Gas Tungsten Arc Welded AISI 4340 Aeronautical and AISI 304 L Austenitic Stainless Steel Dissimilar Joints
In this research work, the weldability of low alloyed AISI 4340 aeronautical steel and AISI 304L austenitic stainless steel joined by continuous current (CC) and pulsed current (PC) gas tungsten arc welding (GTAW) techniques, using ER309L and ERNiCr-3 filler metals was investigated. The main focus of the study involves the investigation on the effect of cont
Mat. Res.. Publicado em: 2015-02
-
12. Desenvolvimento de união de multimateriais através de rebitagem por injeção (Injection Clinching Joining) / Development of multimaterial joints through injection clinching joining
Multimaterial structures are currently a technologically attractive field of research. The growing use of polymer composites replacing metals in structures aiming for weight and emission reduction is part of the motivation of this study. The currently used techniques adhesive bonding and mechanical fastening are limited in certain aspects, opening a path for
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 22/06/2011