Machining Process
Mostrando 13-24 de 122 artigos, teses e dissertações.
-
13. Estudio de los parámetros de proceso del anodizado por plasma químico en Ti-6Al-4V ELI para implantes dentales
ABSTRACT In order to study the variation effect of some parameters of micro-arc oxidation process (MAO) on Ti-6Al-4V samples for dental implants, several treatments were carried out under different conditions of current density, exposure time and electrolyte chemical composition. These processes resulted in generated bioactive titanium oxide surface coatings
Matéria (Rio J.). Publicado em: 19/07/2018
-
14. Evaluation of the oil flow using the MQL technique applied in the cylindrical plunge grinding of AISI 4340 steel with cbn grinding wheel
Abstract The grinding process is defined as an abrasive cutting action of a tool known as grinding wheel, which is submitted to high rotations, promoting excellent finishing and accuracy in dimensions, respecting the parameters established in each project. During the machining, the cutting edges of the abrasive grains undergo wearing and this increases the c
REM, Int. Eng. J.. Publicado em: 2018-07
-
15. Influence of water in the MQL technique in the grinding of steel AISI 4340 using CBN wheels
Abstract Usually, machining employs cooling methods to avoid high temperatures. In most cases, the cutting fluid is applied with high flow and low pressures. This technique consumes a large amount of cutting fluid that causes serious problems in the environment and in the health of the worker. An alternative to the conventional cooling method is the Minimum
REM, Int. Eng. J.. Publicado em: 2018-07
-
16. Study of the AISI 52100 Steel Reuse Through the Powder Metallurgy Route Using High Energy Ball Milling
The AISI 52100 is a tool steel used in industry to produce bearings. After the end of its life cycle, it is remelted or discarded in deposits. The powder metallurgy rises as an alternative to recycle this material without any waste. The steps used to produce the AISI 52100 steel by powder metallurgy included: Machining with speed of 45 rpm, high energy ball
Mat. Res.. Publicado em: 06/11/2017
-
17. Residual Stresses Analysis in Ball end Milling of Nickel-Based Superalloy Inconel 718
Inconel 718 is widely used in the aviation, space, automotive and biomedical industries because of its outstanding properties. Near-surface residual stresses that are induced by ball end milling in Inconel 718 can be crucial for the performance and service time of the machined parts. In this paper, the influences of cutting conditions, including the use of c
Mat. Res.. Publicado em: 18/09/2017
-
18. Investigation of High-Speed Cryogenic Machining Based on Finite Element Approach
Abstract The simulation of cryogenic machining process because of using a three-dimensional model and high process duration time in the finite element method, have been studied rarely. In this study, to overcome this limitation, a 2.5D finite element model using the commercial finite element software ABAQUS has been developed for the cryogenic machining proc
Lat. Am. j. solids struct.. Publicado em: 2017-03
-
19. Surface Integrity Analysis in Machining of Hardened AISI 4140 Steel
This study aimed to analyze the residual stresses and roughness in finishing milling of AISI 4140 steel, quenched and tempered up to hardness of 58 HRC. Machining operations were performed with the use of CBN inserts and by varying three basic cutting parameters (cutting speed, feed per tooth and cutting depth). Hardened materials are typically machined by a
Mat. Res.. Publicado em: 23/01/2017
-
20. Evolución Microestructural en Uniones de la Aleación Ti-6Al-4V Mediante el Proceso de Soldadura de Punto por Fricción-agitación
Abstract Friction stir spot welding (FSSW) is a process of recent development and interest, mainly in titanium alloys, since there are previous studies of aluminum alloys, magnesium, steel and polymers. Titanium alloys have a wide range of applications in the aeronautical industry, mainly in the components of commercial aircrafts as landing gear. Therefore,
Soldag. insp.. Publicado em: 2016-06
-
21. Machinability Evaluation in Hard Milling of AISI D2 Steel
Milling of hardened steel components provides considerable benefits in terms of reduced manufacturing cost and time compared to traditional machining. Temperature variation in milling is an important factor affecting the wear of cutting tools. The poor selection of milling parameters may cause excessive tool wear and increased work surface roughness. Hence,
Mat. Res.. Publicado em: 01/03/2016
-
22. The Influence of Twist Drill Main Cutting Edge Preparation in Drilling Process
In order to improve the performance of a twist drill, one must understand some aspects involved in drilling process that are not commonly addressed, such as the micro geometry employed in the tool’s tip sharpening and the protection of the main cutting edge. The edge of the twist drill can be protected by rounding, chamfering or the combination of both. Th
Mat. Res.. Publicado em: 17/11/2015
-
23. Location Issues of Thin Shell Parts in the Reconfigurable Fixture for Trimming Operation
ABSTRACT: The location of thin shell parts is always a knotty problem during machining, welding, forming, assembling and inspection operations. This paper mainly focuses on the special location issues in the digital and flexible trimming process for aircraft skins fastened by reconfigurable fixture. Firstly, in view of the dynamic change of effective locator
J. Aerosp. Technol. Manag.. Publicado em: 2014-09
-
24. Residual stress analysis of drive shafts after induction hardening
Typically, for automotive shafts, shape distortion manifests itself in most cases after the induction hardening by an effect known as bending. The distortion results in a boost of costs, especially due to machining parts in the hardened state to fabricate its final tolerances. In the present study, residual stress measurements were carried out on automotive
Mat. Res.. Publicado em: 03/06/2014