Lubrication
Mostrando 25-36 de 149 artigos, teses e dissertações.
-
25. Protic Ionic Liquids Used as Metal-Forming Green Lubricants for Aluminum: Effect of Anion Chain Length
Among the applications for protic ionic liquids (PILs), lubrication is one of the newest and the most promising. In this work, ammonium-based protic ionic liquids were tested as lubricant fluids for aluminum-steel contacts. PILs were synthesized with 2-hydroxyethylamine (2HEA) and a carboxylic acid (formic and pentanoic), aiming to understand the effect of t
Mat. Res.. Publicado em: 03/04/2017
-
26. Female sexual function following a novel transobturator sling procedure without paraurethral dissection (modified-TOT)
ABSTRACT Purpose To determine whether there is a difference in sexual function after modified and classical TOT procedures. Materials and Methods Of the 80 sexually active women with SUI, 36 underwent an original outside-in TOT as described by Delorme, and 44 underwent modified TOT procedure, between 2011 and 2015. The severity of incontinence and sexual
Int. braz j urol.. Publicado em: 2017-02
-
27. Colleters in Chamaecrista (L.) Moench sect. Chamaecrista and sect. Caliciopsis (Leguminosae-Caesalpinioideae): anatomy and taxonomic implications
ABSTRACT The genus Chamaecrista contains ca. 330 species organized into six sections, of which section Chamaecrista is the second largest (ca.75 species) distributed among six series, while the section Caliciopsis contains only two species. Colleters have been described in the genus Chamaecrista and they show potential taxonomic and phylogenetic significance
Acta Bot. Bras.. Publicado em: 30/01/2017
-
28. The Lubricity Analysis of Cutting Fluid Emulsions
The new generation of cutting fluids should have some characteristics, such as low toxicity and biodegradability. A bio-cutting fluid emulsion are an excellent option because they present those properties, as well as good mechanical performance. The present study aims to investigate the lubricity of O/W emulsions (cutting fluid emulsion), varying the concent
Mat. Res.. Publicado em: 2017
-
29. Effect of surface finishing on friction and wear of Poly-Ether-Ether-Ketone (PEEK) under oil lubrication
Abstract The tribological properties of poly-ether-ether-ketone (PEEK) containing 30% of carbon fiber were studied in an oil-lubricated environment and different surface finishing of the metallic counterbody. Four different finishing processes, commonly used in the automotive industry, were chosen for this study: turning, grinding, honing and polishing. The
Polímeros. Publicado em: 08/12/2016
-
30. Study of oxide nanoparticles as additives for vegetable lubricants
Currently, vegetable oils have been studied as biolubricants in order to reach new environmental standards. Besides being non-renewable, mineral oils from petroleum bring consequences to the environment due to its low biodegradability. Thus, the aim of this work is to develop a biolubricant and to add oxide nanoparticles (ZnO and CuO) in order to improve abr
Mat. Res.. Publicado em: 2014-10
-
31. Evaluation of different methods of cooling-lubrication in cylindrical grinding of advanced ceramic dip
The current work presents a study of alternative methods of cooling-lubrication for the external plunge grinding of advanced ceramics using diamond wheels. These two alternative methods, which are intended to reduce cutting fluid expenses, are commonly referred to as the optimized cooling-lubrication method and minimal quantity of lubrication (MQL). The tech
Mat. Res.. Publicado em: 30/09/2014
-
32. Analysis of surface roughness and hardness in titanium alloy machining with polycrystalline diamond tool under different lubricating modes
The present work deals with the investigation on machining of difficult-to-machine material titanium alloy (Ti-6Al-4V) using poly crystalline diamond (PCD) tool under different coolant strategies, namely dry, flooded and MQL. Taguchi technique has been employed and the optimization results indicated that MQL lubricating mode with cutting speed of 150 m/min,
Mat. Res.. Publicado em: 15/08/2014
-
33. Micro and nanometric wear evaluation of metal discs used on determination of biodiesel fuel lubricity
The contact of diesel fuel with engine subsystems demands a good wear resistance. Lubricity is an important feature for integrity of injection system and the sulphur composites are primarily responsible for lubrication of the injector nozzle. Biodiesel is responsible for partially restoring the lubricity of diesel fuel that presents low levels of sulphur com
Mat. Res.. Publicado em: 04/07/2014
-
34. Utilization of teflon and aluminum oxide for wheel cleaning in Minimum Quantity Lubrication (MQL) grinding
Researches concerning cooling-lubrication optimization in grinding have been conducted to contribute to a more sustainable process. An alternative to flood coolant is minimum quantity lubrication (MQL), which spray oil droplets in a compressed air jet. However, problems related to wheel cleaning were reported, due to wheel loading by a mixture of chips and o
Mat. Res.. Publicado em: 05/11/2013
-
35. Sexual dysfunction and cardiovascular diseases: a systematic review of prevalence
The aim of this study was to conduct a systematic review of the literature regarding the prevalence of sexual dysfunction in patients with cardiovascular diseases. An article search of the ISI Web of Science and PubMed databases using the search terms "sexual dysfunction”, “cardiovascular diseases”, “coronary artery disease", “myocardial infarct"
Clinics. Publicado em: 2013-11
-
36. Utilization of minimum quantity lubrication (MQL) with water in CBN grinding of steel
The use of cutting fluids is fundamental to machining processes, mainly when it comes to high heat generation, which is the case of grinding. Thus, lubrication and cooling provided by cutting fluids improve the final quality of the workpiece. However, cutting fluid usage provide some drawbacks concerning environmental, costs and health issues. Therefore, new
Mat. Res.. Publicado em: 08/10/2013