Inconel 625
Mostrando 1-12 de 22 artigos, teses e dissertações.
-
1. Study on influence of the PTA-P welding process parameters on corrosion behavior of Inconel 625 coatings
ABSTRACT In the present work, PTA welding process was used to investigate the influence of welding parameters on the dilution, microhardness and corrosion resistance of Inconel 625 alloy coatings on the API 5L X70 grade steel. The electrochemical impedance spectroscopy (EIS) and linear potentiodynamic polarization (LPP) measurements were used to study the pr
Matéria (Rio J.). Publicado em: 20/05/2019
-
2. Performance of the INCONEL 625 alloy weld overlay obtained by FCAW process
ABSTRACT Nickel-based weld overlays (cladding) are commonly used in oil & gas industry to extend the life of equipment under corrosive environment, as it improves the corrosion resistance without a significant increase in the manufacturing cost, when compared to a full nickel-based alloy equipment. Although there are extensive literature involving overlays a
Matéria (Rio J.). Publicado em: 20/05/2019
-
3. Characterization of Phase Transformations and Microstructural Changes in an API 5CT L80 Steel Grade During Ni Alloy Laser Cladding
The superficial coatings in micro-alloyed steel pipes has been a pointed way to decrease the corrosion problems in oil and gas industry. However, little emphasis has been given to the substrate. The effects of the deposition method on the steel microstructure and properties are still not well described. In this context, this work studied the effect of Ni sup
Mat. Res.. Publicado em: 26/07/2018
-
4. Fracture Behavior and Fatigue Performance of Inconel 625
Inconel 625 is a nickel-based highly-resistant superalloy widely used in aerospace components, in the nuclear industry, and especially in the maritime industry. Materials such as Inconel 625 have been widely used in oil exploration of Brazilian pre-salt layers due to their excellent resistance to corrosion under tension, pitting and crevice corrosion by chlo
Mat. Res.. Publicado em: 25/06/2018
-
5. Effect of Residual Stresses of GTA Welding for Dissimilar Materials
The purpose of the present work is to understand the evolution of residual stresses in weldments. The study made to weld the multipass dissimilar of Nickel-based superalloy Inconel 625 and stainless steel 316L using Continuous Current Gas Tungsten Arc Welding (CCGTAW) and Pulsed Current Gas Tungsten Arc Welding (PCGTAW) process employing ERNiCrMo-3 and ERNiC
Mat. Res.. Publicado em: 25/06/2018
-
6. Efeito dos Tratamentos Térmicos de Normalização e de Solubilização na Microestrutura de uma Junta Dissimilar Soldada entre um Tubo de Aço API 5L X-52 e o Inconel 625
Resumo O propósito deste trabalho é comparar as mudanças na microestrutura e na dureza de um tubo de aço API 5L X-52, revestido internamente por soldagem com Inconel 625, após a execução dos tratamentos térmicos de normalização a 1100 °C por 60 min. e resfriamento ao ar, e de solubilização a 1030 °C com aquecimento por indução eletromagnétic
Soldag. insp.. Publicado em: 21/12/2017
-
7. Evaluation of the Influence of Surface Finishing on the Corrosion Resistance of HVOF Applied Inconel 625 Coatings on Steel
In this work, the corrosion resistance of Inconel 625 coatings applied to AISI 4140 steel plates was evaluated. Coatings were produced by High Velocity Oxygen Fuel (HVOF) by use of two different equipment which use either kerosene (liquid) or propane (gas) as fuel. The resulting coatings were evaluated in two conditions: as-deposited and after a surface fini
Mat. Res.. Publicado em: 18/12/2017
-
8. Microstructure and Mechanical Properties of Borided Inconel 625 Superalloy
ABSTRACT The Ni- based superalloy Inconel 625 is extensively used owing to its high strength, excellent fabricability, good weldability and outstanding resistance to high temperature corrosion against aggressive environments. However, despite its unique properties and extensive use, its wear resistance is in some cases unsatisfactory. In this study, Inconel
Matéria (Rio J.). Publicado em: 22/06/2017
-
9. Evaluation of hydrogen-Induced cracking resistance of the In625 laser coating system on a C-Mn steel substrate
Abstract The corrosion of C-Mn steels in the presence of hydrogen sulfide (H2S) represents a significant challenge to oil production and natural gas treatment facilities. The failure mechanism induced by hydrogen-induced cracking (HIC) in a Inconel 625 coating / C-Mn steel has not been extensively investigated in the past. In the present work, an API 5CT ste
REM, Int. Eng. J.. Publicado em: 2017-06
-
10. Caracterização de Uma Junta Dissimilar entre Aço Carbono e Inconel 625 Obtida por Soldagem por Explosão
Resumo Neste trabalho é caracterizada uma junta dissimilar entre aço carbono e inconel 625 obtida pela soldagem por explosão. A caracterização metalográfica foi feita com uso de diferentes ataques químicos e observação microestrutural do metal de base (MB), a interface e o revestimento de inconel 625 por meio de microscopia ótica (MO), microscopia
Soldag. insp.. Publicado em: 2017-03
-
11. Avaliação das Tensões Residuais em Juntas Soldadas de Inconel 625 Obtidas Através da Soldagem por Fricção e Mistura Mecânica
Resumo A utilização de materiais nobres é requisito básico em aplicações onde existe um ambiente agressivo como na indústria do petróleo e nuclear. Neste panorama, a liga Inconel 625 é frequentemente utilizada como material de cladeamento no revestimento interno de dutos rígidos. Assim, as superligas de níquel exercem papel fundamental nos campos
Soldag. insp.. Publicado em: 2017-03
-
12. Estudo de Procedimentos de Soldagem MIG/MAG para Aplicação de Revestimentos de Liga de Níquel Inconel 625 em Aço Estrutural ASTM A387 Gr.11
Resumo O presente trabalho objetiva o estudo de técnicas de soldagem aplicadas a reparo de componentes fabricados em aço ASTM A387 Gr.11, largamente utilizado em aplicações da indústria do petróleo e gás. Devido ao regime de trabalho e necessidade de utilização de materiais com boa resistência mecânica e à corrosão, utilizou-se como metal de adi
Soldag. insp.. Publicado em: 2016-03