Implant Abutment
Mostrando 13-24 de 86 artigos, teses e dissertações.
-
13. Influence of implant-abutment angulations and crown material on stress distribution on central incisor: a 3D FEA
Abstract Aim: To investigate the effect of implant-abutment angulation and crown material on stress distribution of central incisors. Finite element method was used to simulate the clinical situation of a maxillary right central incisor restored by two different implant-abutment angulations, 15° and 25°, using two different crown materials (IPS E-Max CAD
Braz. J. Oral Sci.. Publicado em: 2015-12
-
14. Active Bone Conduction Prosthesis: BonebridgeTM
Introduction Bone conduction implants are indicated for patients with conductive and mixed hearing loss, as well as for patients with single-sided deafness (SSD). The transcutaneous technology avoids several complications of the percutaneous bone conduction implants including skin reaction, skin growth over the abutment, and wound infection. The Bonebridge
Int. Arch. Otorhinolaryngol.. Publicado em: 2015-12
-
15. Morse taper internal connection implants: would abutment reseating influence retention?
Abstract Aim: To investigate whether the removal and reseating of the abutment influences the retention of Morse taper implant system. Methods: Two Morse taper implant systems were selected: Bicon Dental ImplantTM system (Bicon, LLC, Boston, MA, USA) and Kopp Implant(r) system (Kopp(r), Curitiba, PR, Brazil). In both systems, the abutment is connected to
Braz. J. Oral Sci.. Publicado em: 2015-09
-
16. Failure of prosthetic screws on 971 implants
Abstract Aim: To evaluate the presence of failures in prosthetic screws and whether these failures are related to the type of prosthesis, abutment angulation and presence or not of intermediate. Methods: Two-hundred and sixty-seven patients were evaluated at the Federal University of Santa Catarina, totaling 971 external hexagonal implants in place for at
Braz. J. Oral Sci.. Publicado em: 2015-09
-
17. Effect of Using Nano and Micro Airborne Abrasive Particles on Bond Strength of Implant Abutment to Prosthesis
A conexão das próteses nos pilares dos implantes dentários é um fator de preocupação e a obtenção de uma retenção satisfatória tem sido objeto de estudos recentes em próteses com retenção cementária. O jateamento é um método de obter uma superfície áspera para aumentar a retenção. O objetivo d
Braz. Dent. J.. Publicado em: 2015-02
-
18. Strain analysis of different diameter Morse taper implants under overloading compressive conditions
The aim of this study was to evaluate the amount of deformation from compression caused by different diameters of Morse taper implants and the residual deformation after load removal. Thirty Morse taper implants lacking external threads were divided into 3 groups (n = 10) according to their diameter as follows: 3.5 mm, 4.0 mm and 5.0 mm. Two-piece abutments
Braz. oral res.. Publicado em: 23/01/2015
-
19. Fracture resistance of abutment screws made of titanium, polyetheretherketone, and carbon fiber-reinforced polyetheretherketone
Fractured abutment screws may be replaced; however, sometimes, the screw cannot be removed and the entire implant must be surgically removed and replaced. The aim of this study was to compare the fracture resistance of abutment retention screws made of titanium, polyetheretherketone (PEEK) and 30% carbon fiber-reinforced PEEK, using an external hexagonal imp
Braz. oral res.. Publicado em: 04/08/2014
-
20. Bacterial microleakage at the implant-abutment interface in Morse taper implants
AIM: To evaluate the microleakage at the implant-abutment (I-A) interface of Morse tapered implants inoculated with different volumes of bacterial suspension. METHODS: Morse tapered I-A sets were selected and divided in two groups depending on the type of abutment: passing screw (PS) and solid (S), and then subdivided into four subgroups (n=6) accordin
Braz. J. Oral Sci.. Publicado em: 2014-04
-
21. In Vitro Microbiological Analysis of Bacterial Seal at the Implant-Abutment Interface Using Two Morse Taper Implant Models
O objetivo deste estudo foi avaliar comparativamente, por meio de análise microbiológica in vitro, a capacidade de selamento bacteriano de dois modelos de implante de encaixe morse. Foram utilizados 15 implantes com travamento de seus respectivos mini-pilares por fricção, sem auxílio de parafuso (Grupo 1) e 30 implantes com travamento de seus respectivo
Braz. Dent. J.. Publicado em: 2014-01
-
22. Screw loosening of different UCLA-type abutments after mechanical cycling
AIM: To evaluate the loss of applied torque (detorque) values in cast and pre-machined abutments for external hex abutment/implant interface of single implant-supported prostheses subjected to mechanical cycling. METHODS: Ten metal crowns were fabricated using two types of UCLA abutments: cast and pre-machined with metal base in NiCrTi alloy and tightened to
Braz. J. Oral Sci.. Publicado em: 2013-09
-
23. Comparison of methods to evaluate implant-abutment interface
AIM: To compare two main methods of two-dimensional measurement of fit at the implant prosthodontic interface, testing the hypothesis that optical microscopy (OM) can reliably and efficiently scanning electronic microscopy (SEM). METHODS: Four frameworks with four titanium abutments joined with titanium bars were used. The implant-abutment interfaces were ex
Braz. J. Oral Sci.. Publicado em: 2013-03
-
24. Analysis by the finite element method of the stress distribution in prosthetic components placed in implants with morse cone connection in the anterior maxilla / Análise pelo método dos elementos finitos da distribuição de tensões em componentes protéticos posicionados em implantes com conexão cone morse na região anterior da maxila
The aim of this study was to evaluate through the three-dimensional method of the finite elements the stress distribution in the bone / implant interface and implant / abutment on implants with morse cone connection, placed in the anterior maxilla. From a virtual reconstruction of bone from a CT scan, cantilever prosthesis (11-21) was simulated using prosthe
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 02/08/2012