Flat Plate
Mostrando 1-12 de 85 artigos, teses e dissertações.
-
1. Effect of Multi-Pass Rolling on the Performance of AZ31 Magnesium Alloy Anode in Mg-Air Battery
In this work, the influence of rolling passes on microstructure, corrosion behavior, electrochemical performance, and battery performance of AZ31 magnesium alloy was studied. The experimental results show that the grain size decreases first and then increases with rolling passes. Among them, the grain size of three passes rolled sample is the smallest, while
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
2. HYBRID SYSTEM SIMULATION TO SUPPLY HEATED AIR TO A SOLAR FOOD DRYER
ABSTRACT The intermittence of solar radiation, due to continuous rainy or cloudy days, is a limitation of simple and small solar dryers. These conditions often make them impossible to use. By including storage systems (thermal accumulation) and/or auxiliary energy sources, drying processes or dehydration can be conducted continuously, even during periods of
Eng. Agríc.. Publicado em: 2020-04
-
3. Nonlinear numerical analysis of composite slabs with steel decking
Resumo O comportamento das lajes mistas é governado pelo cisalhamento longitudinal na interface entre o aço e o concreto, que é desenvolvido em lajes sob flexão simples. O método m-k e o método da interação parcial, utilizados no cálculo da resistência ao cisalhamento na interface aço-concreto de lajes mistas, são baseados em ensaios experimentai
Rev. IBRACON Estrut. Mater.. Publicado em: 11/11/2019
-
4. Microstructural Evolution Due to One Thermal Cycle in a Superduplex Stainless Steel ASTM A890/A890M - Grade 6A in the As-Weld and Post-Weld Heat Treatment Conditions
During welding of the superduplex stainless steels are exposed to thermal cycles, allowing precipitation of deleterious phases as well as unbalance as the ferrite and austenite phases. This work analyzed the microstructural changes taking place on a plate ASTM A890/A890M - grade 6A steel submitted to arc welding one welding of pass conducted on a flat surfac
Mat. Res.. Publicado em: 08/08/2019
-
5. Castor polyurethane used as osteosynthesis plates: microstructural and thermal analysis
Abstract Bone fractures to be corrected need stabilization of their extremities, which is achieved with the use of plates and screws. This research aimed to produce castor bean polyurethane (Ricinus communis), to make resorbable plate, structural and thermal analysis. The production was made by the glycerolysis of the triglycerides present in the oil, after
Polímeros. Publicado em: 04/07/2019
-
6. Characterization of new selective coatings, made of granite and chrome, for solar collectors
ABSTRACT The depletion of fossil fuel reserves and climate change caused by atmospheric pollution has led the human being to seek alternatives that are less damaging to the environment. The concern and the awareness of the population open space for the study of renewable energies to be deepened, among them the best use of solar energy. The use of alternative
Matéria (Rio J.). Publicado em: 10/06/2019
-
7. Escolha das Energias de Soldagem para Aplicação na Técnica da Dupla Camada na Soldagem do Aço ASTM 131 Grau AH 36
Resumo Durante o processo de soldagem o aço microligado ASTM A131 Grau AH36 pode apresentar defeitos oriundos dos ciclos térmicos (distorções) que demandarão procedimentos onerosos como o tratamento térmico pós-soldagem. Somando-se a isto, este aço não é indicado a sofrer normalização, normalização seguida por revenimento, ou por têmpera e rev
Soldag. insp.. Publicado em: 09/05/2019
-
8. Uma Metodologia para Análise da Distribuição de Contagem dos Picos de Tensão de Reignição para Avaliação da Estabilidade do Processo GMAW Curto-Circuito
Resumo A estabilidade do arco tem sido estudada através de análises estatísticas obtidas dos sinais de tensão de arco e corrente de soldagem. Histogramas e cálculo de estatísticas dos parâmetros tempo de arco aberto e tempo de curto circuito são meios de avaliação da estabilidade dos processos de soldagem. Contudo, estudos relacionados aos picos de
Soldag. insp.. Publicado em: 09/05/2019
-
9. Passive vibration control using a metaconcrete thin plate
Abstract We investigated the band structure of flexural waves propagating in a metaconcrete thin plate, consisting of a concrete matrix reinforced by steel inclusions coated by rubber in square and triangular lattices. We considered the classical Kirchhoff-Love thin plate theory. We also studied the influence of inclusion geometry - circular, square and rota
Cerâmica. Publicado em: 2019-01
-
10. Proper Orthogonal Decomposition and Spectral Analysis of a Wall-Mounted Square Cylinder Wake
ABSTRACT: The flow patterns over a finite square cylinder of aspect ratio of 3 were analyzed experimentally in a subsonic wind tunnel using the time-resolved particle image velocimetry (TR - PIV) techniques. The near wake flow structures and vortex shedding characteristics were investigated using mean flow analysis, spectral analysis and proper orthogonal de
J. Aerosp. Technol. Manag.. Publicado em: 03/05/2018
-
11. An interface element for numerical analysis of flat plate/shell elements with deformable connection
Abstract The use of numerical methods such as the finite elements method for solving structural analysis problems is becoming ever more efficient. An interface element capable of associating flat plate/shell element in three different combinations has been developed. In a structural analysis, when only the flat plate/shell’s finite elements are used in th
Lat. Am. j. solids struct.. Publicado em: 26/04/2018
-
12. Analysis of fouling and juice quality in crossflow ultrafiltration of watermelon juice
Abstract Raw watermelon juice was clarified in a laboratory scale flat plate ultrafiltration system incorporating polyethersulphone membranes with a molecular weight cut-off of 50 kDa. The experiments have been carried out over a wide range of trans-membrane pressures (1-3 bar). The effect of ultrafiltration with molecular weight cut-off (MWCO) of 50 kDa PES
Food Sci. Technol. Publicado em: 26/10/2017