Direct Numerical Simulation
Mostrando 1-12 de 57 artigos, teses e dissertações.
-
1. 3D numerical investigation of mixture formation and combustion in a DISI engine at part-load under stratified operation
This work investigates through numerical simulation, the operation of a big bore direct fuel injection spark ignition engine, at part load under stratified operation. It evaluates fuel-air mixture preparation and combustion process with the adoption of detailed chemical kinetics mechanisms for both Isooctane and Ethanol, and applying adaptive mesh refinement
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 2020
-
2. Study on elastoplastic coupling mechanics model of the milled mixture of sugar cane
Abstract At present, the phenomenon of elastoplastic coupling isn’t considered in establishing the mechanics model of the milled mixture of sugar cane. In order to describe elastoplastic coupling and yield characteristics, based on uniaxial confined compression tests and direct shear tests, the evolution of the elastic parameters of the solid fiber with v
Food Sci. Technol. Publicado em: 11/04/2019
-
3. Direct Numerical Simulation of a Compressible Flow and Matrix-Free Analysis of its Instabilities over an Open Cavity
ABSTRACT: This study takes a Jacobian-free approach based on the Arnoldi iteration to present a method to perform hydrodynamic instability analysis based on Direct Numerical Simulations. The method employs high order spatial and temporal discretizations for the flow simulation and has very low requirements of computational time and memory, compared to conven
J. Aerosp. Technol. Manag.. Publicado em: 19/07/2018
-
4. Direct Numerical Simulation Code Validation for Compressible Shear Flows Using Linear Stability Theory
ABSTRACT: In order to simulate compressible shear flow stability and aeroacoustic problems, a numerical code must be able to capture how a baseflow behaves when submitted to small disturbances. If the disturbances are amplified, the flow is unstable. The linear stability theory (LST) provides a framework to obtain information about the growth rate in relatio
J. Aerosp. Technol. Manag.. Publicado em: 07/05/2018
-
5. Mathematical modeling of the shaft furnace process for producing DRI based on the multiphase theory
Abstract A numerical model based on transport equations for momentum, energy and chemical species for the gas and solid phases is proposed to simulate the inner phenomena in the direct reduction of the shaft furnace process for producing directly reduced iron (DRI). The model is verified using industrial data for productivity, raw materials and final composi
REM, Int. Eng. J.. Publicado em: 2018-03
-
6. Investigation on the Effects of Process Parameters on Laser Percussion Drilling Using Finite Element Methodology; Statistical Modelling and Optimization
Abstract In the present research, the simulation of the Nickel-base superalloy Inconel 718 fiber-laser drilling process with the thickness of 1mm is investigated through the Finite Element Method. In order to specify the appropriate Gaussian distribution of laser beam, the results of an experimental research on glass laser drilling were simulated using three
Lat. Am. j. solids struct.. Publicado em: 2017-03
-
7. LINEAR STABILITY ANALYSIS AND CFD SIMULATION OF DOUBLE-LAYER RAYLEIGH-BÉNARD CONVECTION
Abstract Natural convection in superimposed layers of fluids heated from below is commonly observed in many industrial and natural situations, such as crystal growth, co-extrusion processes and atmospheric flow. The stability analysis of this system reveals a complex dynamic behavior, including the potential multiplicity of stationary states and occurrence o
Braz. J. Chem. Eng.. Publicado em: 2016-09
-
8. On the Validation of a Numerical Model for the Analysis of Soil-Structure Interaction Problems
Abstract Modeling and simulation of mechanical response of structures, relies on the use of computational models. Therefore, verification and validation procedures are the primary means of assessing accuracy, confidence and credibility in modeling. This paper is concerned with the validation of a three dimensional numerical model based on the finite element
Lat. Am. j. solids struct.. Publicado em: 2016-08
-
9. Microstructure and Liquid Phase Separation of CuCr Alloys Treated by High Current Pulsed Electron Beam
Microstructures of CuCr25 and CuCr50 alloys treated by high current pulsed electron beam (HCPEB) were investigated in this work. The microstructure and solidification behavior of the Cr-rich phases were characterized by scanning electron microscopy (SEM). Results show that a remelting layer of 3~5 μm is formed on the surface of Cu-Cr alloys. The microstruct
Mat. Res.. Publicado em: 23/10/2015
-
10. Direct Numerical Simulation of the Onset of Vortex Shedding for Blunt Elongated Bodies
ABSTRACT: This research project focuses upon the wake behind a two-dimensional blunt-trailing-edged body. Data are obtained numerically by means of a Direct Numerical Simulation code. The body has an elliptical nose followed by a straight section that ends in a blunt base. The present paper is dedicated to the analysis of the onset of the shedding process. T
J. Aerosp. Technol. Manag.. Publicado em: 2014-09
-
11. A New Coupled Free Wake-CFD Method for Calculation of Helicopter Rotor Flow-Field in Hover
ABSTRACT: This paper concerns a new coupled free wake-CFD method for proper calculation of aerodynamic loads on a two bladed helicopter rotor in hovering flight. Loading is computed by solving the three dimensional Euler equations in a rotating coordinate system. However, since direct simulation of the tip vortices and wake requires a very fine grid, the rot
J. Aerosp. Technol. Manag.. Publicado em: 2014-06
-
12. Simulação da dinâmica do estado excitado em semicondutores orgânicos / Simulation of the excited state dynamics in organic semiconductors
In the present work, the Monte Carlo method and the direct numerical integration of the Master Equation were employed to simulate the excitation spectral diffusion process in light emitting polymeric systems. The methodology employed a competition among the internal intra-molecular relaxation, the inter-molecular incoherent energy transfer via Förster mecha
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 25/04/2012