Cracks
Mostrando 1-12 de 335 artigos, teses e dissertações.
-
1. Mix design formulation range for metakaolin-based geopolymer synthesis
Abstract This article presents a range of mix design formulations to obtain metakaolin-based geopolymer synthesis. Geopolymer samples were synthesized from metakaolin, a 10 M sodium hydroxide solution, and alkaline sodium silicate. These three components were mixed in different proportions to form a paste which was molded in a cylindrical shape, set at room
REM - International Engineering Journal. Publicado em: 2022
-
2. Flexible pavement overlay design of UFJF ring road based on the new Brazilian mechanistic-empirical pavement design method
Abstract The procedures for design and reinforcement projects regarding flexible pavements available in Brazil are mostly based on empirical models developed from studies carried out in specific localities, and therefore, should only be used in cases where equivalent climatic and traffic conditions are observed. The national highway agencies in partnership w
REM, Int. Eng. J.. Publicado em: 2020-12
-
3. Analysis of cracks and coating in iron ore pellets by digital image processing
Abstract The pelletizing process agglomerates ore fines previously considered as tailings and makes its application possible in the form of pellets. During the process, the pellets are subjected to various compressive forces and temperature changes, which cause ruptures in their surface. These ruptures (cracks) impair the performance of the pellets in the re
REM, Int. Eng. J.. Publicado em: 2020-09
-
4. Discrimination of pores and cracks in iron ore pellets using deep learning neural networks
Abstract The discrimination between pores and cracks is an important step in the microstructural analysis of iron ore pellets. While the porosity is fundamental during the reduction process in blast furnaces, cracks are strongly detrimental to the mechanical strength. The usual image processing tools cannot automatically discriminate between these two types
REM, Int. Eng. J.. Publicado em: 2020-06
-
5. BACTERIAL NANOCELLULOSE BIOMEMBRANE AS A SUPPORT FOR HUMAN INSULIN AIMING AT TRANSDERMAL PERMEATION
Production of bacterial nanocellulose was pursued as a matrix system for the stabilization of human insulin. The biomembranes produced by Gluconacetobacter hansenii were washed with 2% aqueous sodium dodecylsulfate solution, rinsed with ultrapure water and immersed in 1 mol L-1 NaOH aqueous solution at 60 °C for 90 min until neutralization. For the insulin
Quím. Nova. Publicado em: 2020-05
-
6. Resorcinolic Lipids from Yucatecan Propolis
Propolis is a material produced by bees from a combination of plant exudates and wax, used to fill out cracks in the beehive and to defend against intruders and pathogenic microorganisms; it is recognized for its many biological activities and its chemical composition depends on the botanical sources close to the beehive. The objective of this investigation
J. Braz. Chem. Soc.. Publicado em: 2020-01
-
7. Numerical implementation of a micromechanics-based viscoelastic model for geomaterials with isotropically distributed micro-fractures
Abstract The constitutive behavior of geomaterials is generally affected by the presence at different scales of discontinuity surfaces with different sizes and orientations. According to their mechanical behavior, such discontinuities can be distinguished as cracks or fractures. Fractures are interfaces that can transfer normal and tangential stresses, where
Lat. Am. j. solids struct.. Publicado em: 25/11/2019
-
8. Estimação da profundidade de fissuras em concreto através da velocidade de ondas ultrassônicas
RESUMO As fissuras são as manifestações patológicas mais recorrentes no concreto, devido as diferentes formas de exposição que o material está sujeito. Neste cenário, é importante que as edificações passem por inspeções através de diferentes métodos, dentre os quais os ensaios não destrutivos (END) aparecem como ferramenta alternativa. Dentre
Matéria (Rio J.). Publicado em: 25/11/2019
-
9. Efeito da adição de resíduo de vidro em massa de cerâmica de alvenaria
RESUMO Este trabalho investigou o efeito da adição de resíduo de vidro para fabricação de cerâmica de alvenaria. Foram conformados corpos-de-prova cilíndricos de 27 mm de diâmetro por 45 mm de altura, a partir da massa padrão de uma indústria de cerâmica vermelha e outras 3 formulações (5, 10 e 20%) com incorporação de vidro, baseado em estudo
Matéria (Rio J.). Publicado em: 25/11/2019
-
10. Impactos Socioeconômicos, Ambientais e Tecnológicos Causados pela Instalação dos Parques Eólicos no Ceará
Resumo O Estado do Ceará se destaca no processo de produção de energia proveniente dos ventos por possuir posição geográfica privilegiada na geração de energia eólica. Esse trabalho consiste em apresentar os impactos ambientais, sociais, econômicos e tecnológicos originados com a implantação e operação das Usinas Eólicas no litoral cearense a
Rev. bras. meteorol.. Publicado em: 21/10/2019
-
11. Reinforced Glass-ceramics: Parametric Inspection of Three-Dimensional Wear and Volumetric Loss after Chewing Simulation
Resumo O objetivo deste estudo foi investigar o desgaste tridimensional, perda volumétrica e rugosidade após a simulação de mastigação de dois materiais vitro-cerâmicos. Discos de dissilicato de lítio (LD, Emax CAD, Ivoclar) e silicato de lítio reforçado com zircônia (ZLS, Vita Suprinity, Vita Zhanfabrick) (n=20/g) foram confeccionados e digitaliz
Braz. Dent. J.. Publicado em: 07/10/2019
-
12. Concrete block structural masonry beam shear design: theoretical and experimental analysis and recommendations to the brazilian standards
Resumo Vigas são submetidas à flexão e cisalhamento, sendo esse último esforço o tema desta pesquisa. O objetivo deste trabalho é analisar especificações para dimensionamento ao esforço cortante de vigas de alvenaria estrutural em blocos de concreto, a partir de extensa avaliação da literatura e de ensaios experimentais aqui relatados. A partir de
Rev. IBRACON Estrut. Mater.. Publicado em: 23/09/2019