Compatibilizer
Mostrando 1-12 de 57 artigos, teses e dissertações.
-
1. Preparation of Syntactic Foams made from Green Polyethylene and Glass Microspheres: Morphological and Mechanical Characterization
Polymeric syntactic foams are composites made from the mixture of Hollow Glass Microspheres (HGM) and polymer matrices. One of their main characteristics is their low density and the production of these composites using a matrix derived from renewable sources potentiates their development without neglecting sustainability. In this paper , the properties of H
Mat. Res.. Publicado em: 11/11/2019
-
2. Grafting polypropylene over hollow glass microspheres by reactive extrusion
Abstract Hollow glass microspheres HGM are light, round, hollow, hydrophilic microspheres used to produce polyolefin composites with reduced density. To maintain mechanical strength, it is necessary to improve the adhesion between the polymer matrix and the microspheres, which is done by a compatibilizer. For polypropylene composites a maleic anhydride graft
Polímeros. Publicado em: 10/10/2019
-
3. Avaliação do efeito do agente compatibilizante (PP-g-MA) em misturas PP/Amido termoplástico
RESUMO O crescente desperdício de materiais plásticos no meio ambiente juntamente com a preocupação com a futura escassez do petróleo tem aumentado o interesse por polímeros biodegradáveis, como o amido. Nos últimos anos, o amido tem sido utilizado em misturas com diferentes polímeros sintéticos. Essas misturas têm sido compatibilizadas por meio d
Matéria (Rio J.). Publicado em: 16/09/2019
-
4. Toughening of bio-PE upon addition of PCL and PEgAA
Abstract Researches of polymer blends based on biological and biodegradable polymers appear as a viable alternative to develop environmentally friendly materials. Therefore, the aim of this research was to produce compounds made with biological polyethylene, i.e., Biopolyethylene, Bio-PE, added to the biodegradable Polycaprolactone (PCL) and functionalized b
REM, Int. Eng. J.. Publicado em: 19/06/2019
-
5. Compatibility and characterization of Bio-PE/PCL blends
Abstract In this work, blends based on environmentally friend polymers such as Biopolyethylene (Bio-PE), Polycaprolactone (PCL) and Polyethylene graft maleic anhydride (PEgMA) added as compatibilizer agent were produced by conventional extrusion, aiming to produce bio-blends with synergic properties at low processing cost, being at same time non-polluting an
Polímeros. Publicado em: 10/06/2019
-
6. THE MULTIROLE OF MODIFIED NATURAL GUMS FOR MULTICOMPONENT POLYMERS: AS COUPLING AGENTS FOR POLYMERS REINFORCED WITH CELLULOSIC FIBERS OR COMPATIBILIZERS FOR BIODEGRADABLE POLYMER BLENDS
In this work, the capability to use pine rosin as a biodegradable coupling agent/compatibilizer is studied. To formulate composites, post-consumer polypropylene and discarded agave fibers (as reinforcing agent) are coupled with pine rosin (in pure or maleated form). Besides, poly(lactic acid) (PLA) with poly(butylene adipate-co-terephthalate) (PBAT) are comp
Quím. Nova. Publicado em: 02/05/2019
-
7. Sericin as compatibilizer in starch/ polyester blown films
Abstract This study investigated the effects of low concentrations of sericin (≤ 1.5 wt%) in starch- poly(butylene-adipate-co-terephthalate) (PBAT) films. The films were produced by blown extrusion and mechanical, barrier and structural properties were determined. Films containing 1.0 and 1.5 wt% sericin showed higher tensile strength (6.41 and 6.59 MPa)
Polímeros. Publicado em: 29/11/2018
-
8. Effects of Rotor Speed on Peroxide/Bismaleimide Cured Polypropylene/Nitrile Rubber Thermoplastic Vulcanizates (TPVs)
Elastomer thermoplastics are a class of polymeric materials that received industry attention due to the possibility of joining the elastic of elastomers with the thermoplastics processability. The synergistic properties are linked to the appropriate processing. This study evaluated the effect of rotor speed during polymer mixing and the dynamic vulcanization
Mat. Res.. Publicado em: 09/08/2018
-
9. Hyperbranched polyester polyol modified with polylactic acid as a compatibilizer for plasticized tapioca starch/polylactic acid blends
Abstract A hyperbranched polyester polyol of the second generation (HBP2) was modified with polylactic acid (HBP2-g-PLA) and employed as a compatibilizer for plasticized tapioca starch (TPS)/polylactic acid (PLA) blends. The effect of the compatibilizer HBP2- g-PLA was evaluated in comparison to the control sample (TPS/PLA blend without HBP2-g-PLA). The tor
Polímeros. Publicado em: 15/03/2018
-
10. Effect of PANI on Thermal, Mechanical and Electromagnetic Properties of HDPE/LLDPE/PANI Composites
In this work, polyaniline (PANI) in emeraldine-base form, synthesized by chemical oxidation polymerization, was protonated with hydrochloric acid (HCl). Composites based on high-density polyethylene (HDPE) and linear-low density polyethylene (LLDPE) blends with PANI were prepared in molten condition using a torque rheometer. The effect of compatibilizer agen
Mat. Res.. Publicado em: 11/12/2017
-
11. A Microrheological Study of Poly(Methyl Methacrylate) Elastomer/Poly(Ethylene Terephthalate) (PMMAelast/PET) Blends
This study involved an evaluation of the influence of phase inversion in poly(methyl methacrylate) elastomer/poly(ethylene terephthalate) binary blends (PMMAelast/PET) and the effect of the addition of poly(methyl methacrylate-glycidyl methacrylate-ethyl acrylate) (MGE) interfacial compatibilizer on the microrheological properties of this polymer blend. Ther
Mat. Res.. Publicado em: 30/11/2017
-
12. Correlation between Processing, Morphology and Impact Resistance of PBT/ABS Blends
To understand the processing influence in an intermeshing corotating twin-screw extrusion (ICTSE) on the morphology and impact properties of the uncompatibilized PBT/ABS (70/30) blend, it was submitted to different processing parameters. In this way both morphology and impact properties (resistance and ductile brittle transition temperature (DBTT) would be a
Mat. Res.. Publicado em: 30/10/2017