Ceramic Coating
Mostrando 13-24 de 64 artigos, teses e dissertações.
-
13. Effect of Flame Spray Deposition Parameters on The Microstructure of Al2 O3 - 13 %TiO2 Coatings Applied Onto 7075 Aluminum Alloy
In this work, the effect of flame spraying parameters on physical, structural and microstructural characteristics of Al2O3 - 13 wt.% TiO2 (AT-13) coatings were studied. NiCrAl and AT-13 feedstock powders were used for spraying a bond coat (BC) and a top coat (TC), respectively, onto a 7075 aluminum alloy substrate. The effect of acetylene-to-oxygen ratio and
Mat. Res.. Publicado em: 10/07/2018
-
14. The influence of Nano-TiO2 and Nano-Al2O3 Particles in Silicate Based Electrolytes on Microstructure and Mechanical Properties of Micro Arc Coated Ti6Al4V Alloy
Ceramic oxide coatings were fabricated on Ti6Al4V alloy by micro arc oxidation (MAO) in silicate electrolytes, with nano-TiO2 and nano-Al2O3 and without nano-additives. Effects of nano additives on the structural and mechanical properties of the MAO coatings were analysed. The MAO coatings were investigated by scanning electron microscopy (SEM), Energy-Dispe
Mat. Res.. Publicado em: 18/06/2018
-
15. Surface, microstructural, and adhesion strength investigations of a bioactive hydroxyapatite-titanium oxide ceramic coating applied to Ti-6Al-4V alloys by plasma thermal spraying
Ti-6Al-4V alloy is employed in implants because of its good mechanical strength, excellent biocompatibility, and good resistance to corrosion in biological environments. Herein, a composite (HAp-TiO2, 50% by volume of both components) coating surface employing Ti-6Al-4V was characterized. Samples were analyzed post fabrication and post heat treatment to anal
Mat. Res.. Publicado em: 28/05/2018
-
16. Characterization of Niobia-alumina Deposited by the Sol-gel Process on Carbon Steel
The precursor sols of Al2O3 and mixed NbxOy/Al2O3 oxides were synthesized by the sol-gel process using acetylacetone to control the reaction kinetics of the organometallic oxides in the mixture. The layers of the precursor sols of Al2O3 and NbxOy/Al2O3 were deposited on AISI steel 1020 by manual immersion (dip coating). The lyophilized sols were characterize
Mat. Res.. Publicado em: 16/04/2018
-
17. Bond strength between a polymer-infiltrated ceramic network and a composite for repair: effect of several ceramic surface treatments
Abstract: The effects of several ceramic surface treatments on bond strength of a polymer-infiltrated ceramic network and resin composite as repair material were evaluated. CAD-CAM blocks of a polymer-infiltrated ceramic network (Vita Enamic) were sliced and subjected to aging process, followed by embedding in acrylic resin. The bonding/repair area was treat
Braz. oral res.. Publicado em: 05/04/2018
-
18. Experimental study on the self-suspending proppant-laden flow in a single fracture
Abstract The flow of proppant-laden fluid (PLF) in the fracture is a typical problem of solid-liquid two phase flow, and the transportation and deposition of proppants are essential to determine the flow conductivity of hydraulic fracturing. The self-suspending proppant with a water soluble surface coating is a newly presented supporting material and has gre
REM, Int. Eng. J.. Publicado em: 2018-04
-
19. Analysis of Compositional Modification of Commercial Aluminum Bronzes to Obtain Functional Shape Memory Properties
In copper-based shape memory alloys (SMAs), some exceptional phenomena, such as the shape memory effect (SME) or superelasticity (SE), are observable. However, commercial aluminum bronzes, Cu3Al-based alloys, do not present these functional properties (SME and/or SE) in their original state. Thus, since one of the main copper-based SMA systems is the Cu-Al-N
Mat. Res.. Publicado em: 17/08/2017
-
20. Nano and Micro Ceramic Membranes from Degradable Templates
Abstract The nano/microstructures with highly porous surface area have attracted tremendous attention, particularly the synthesis and tailoring of porous and hollow materials of high performance. In this paper, an easy method of cost-effective synthesis of hollow ceramic fiber membranes based on Hydroxyapatite, TiO2 and ZrO2 stabilized with Yttrium, is propo
Mat. Res.. Publicado em: 28/07/2016
-
21. Microstructure Evolution and Model Analysis of Al2O3/ZrO2 Hypoeutectic Ceramic During Rapid Solidification
Rapid solidification of the super high-temperature Al2O3/ZrO2 melt was studied by a novel method. The melt was prepared by explosion reaction using Al and Zr(NO3)4 as raw materials and then sprayed to Cu-plate. The heat transfer during the solidification process was analyzed by one-dimensional Finite Element Analysis. The cooling rate of the melt decreased w
Mat. Res.. Publicado em: 04/12/2015
-
22. Preparation and Characterization of PA66/Alumina Composite Membrane
In this study, polymer/ceramic composite membranes were prepared and characterized. The polymer used was polyamide 66 (PA66) deposited by dip coating on the inner surface of α-alumina-based (Al2O3) microporous tube. A coating on the ceramic support surface and the formation of the selective layer was analyzed by scanning electron microscopy (SEM) in membran
Mat. Res.. Publicado em: 2015-08
-
23. Nanostructured Titanium Film Deposited by Pulsed Plasma Magnetron Sputtering (Pdms) on a High Voltage Ceramic Insulator for Outdoor Use
In this study, the cold plasma technique was used to produce nanometric titanium films with hydrophobic and anti-fouling properties. The films where deposited on porcelain electrical insulators surfaces to minimize the effects of leakage current. The magnetron sputtering technique was used with a target of pure titanium sheet, and argon as the ionization gas
Mat. Res.. Publicado em: 2015-08
-
24. Thin films produced on 5052 aluminum alloy by plasma electrolytic oxydation with Red Mud-containing Electrolytes
In this paper, we propose the production of ceramic protective thin films by plasma electrolytic oxidation using red mud-containing electrolytes. The treatments were performed through the application of pulsed voltage (600 V, 200 Hz) during 300 seconds to aluminum samples immersed in electrolytic solutions with 5 g of red mud per liter of distilled water. Th
Mat. Res.. Publicado em: 2014-12