Carbon Steel Welding
Mostrando 1-12 de 27 artigos, teses e dissertações.
-
1. Efeito da Adição de Propileno aos Gases de Proteção Convencionais na Soldagem GMAW Aplicada a Juntas de Topo e Ângulo
Resumo O presente trabalho teve por objetivo avaliar a adição de 1,3% de C3H6 ao CO2 puro e 0,6% de C3H6 à mistura de Ar+25%CO2, na soldagem de aço carbono utilizando o processo Gas Metal Arc Welding (GMAW) aplicado em juntas de topo com chanfro em V e ângulo em T. As soldas foram realizadas utilizando chapas de aço SAE 1020, arame de solda ER70S-6 de
Soldag. insp.. Publicado em: 02/12/2019
-
2. Characterization of Austenite Decomposition in Steels with Different Chemical Concepts and High Potential to Manufacture Seamed Pipes for Oil and Gas Industry
This work presents the characterization of austenite decomposition kinetics in two steels during continuous cooling considering non-deformed austenite grains. Two different chemical concepts of steels were evaluated: low carbon - high manganese and a relatively new concept based on low carbon - low manganese - high niobium contents. Dilatometric experiments,
Mat. Res.. Publicado em: 21/10/2019
-
3. Análise das Propriedades Mecânicas de Juntas de Aço Carbono Estrutural Soldadas pelo Processo Arco Submerso com os Arcos Simples e Duplo (Tandem-Arc)
Resumo Diante de um cenário econômico onde a concorrência é cada vez mais acirrada, a busca por processos, técnicas e equipamentos de soldagem que proporcionem ganhos na produtividade é uma exigência para garantir a competitividade das empresas no mercado. Com o desenvolvimento e a adoção de novas tecnologias é possível inovar os processos convenc
Soldag. insp.. Publicado em: 13/06/2019
-
4. Performance of the INCONEL 625 alloy weld overlay obtained by FCAW process
ABSTRACT Nickel-based weld overlays (cladding) are commonly used in oil & gas industry to extend the life of equipment under corrosive environment, as it improves the corrosion resistance without a significant increase in the manufacturing cost, when compared to a full nickel-based alloy equipment. Although there are extensive literature involving overlays a
Matéria (Rio J.). Publicado em: 20/05/2019
-
5. Influência da microestrutura na resistência ao desgaste microabrasivo de ligas de F-Cr-C e Fe-Cr-C-Nb
ABSTRACT Neste trabalho é feita uma avaliação da influência do teor de cromo e da combinação do cromo e nióbio em ligas de revestimento duro do tipo Fe-Cr-C, na microestrutura e propriedades que envolvam a resistência ao desgaste microabrasivo. Vários estudos têm sido realizados em busca de informações conclusivas sobre este sistema em condiçõe
Matéria (Rio J.). Publicado em: 20/05/2019
-
6. Estudio de la microestructura de un cordón de soldadura de un acero P91 mediante microscopía electrónica de transmisión
ABSTRACT In the present work the microstructural characterization of a single-pass weld of 9Cr1MoVNb P91 steel performed by the flux-cored arc welding (FCAW) process in the “as welding” condition has been carried out by means of transmission electron microscopy. P91 steel offers a good weldability, but the mechanical properties of the welded joints are f
Matéria (Rio J.). Publicado em: 19/07/2018
-
7. Influence of heat treatments on the microstructure and degree of sensitization of base metal and weld of AISI 430 stainless steel
ABSTRACT AISI 430 is a non-stabilized ferritic stainless steel grade with carbon content lower than 0.12%.After hot and cold rolling this material is annealed. The slow cooling after soaking at temperatures between 900oC and 1000oC promotes the formation of a high quantity of carbides and nitrides, while the rapid cooling partially suppresses the formation o
Matéria (Rio J.). Publicado em: 08/01/2018
-
8. Evaluation of Welding Parameter's Effects on Corrosion Behavior of Bronze-Carbon Steel Dual-Layer Explosion Welded Joint at Salt Enviroment
In the current investigation, corrosion behavior and microstructural variations of explosion-welded joint of bronze-carbon steel dual-layer plates were studied. The resultant curves of potentiodynamic's polarization tests demonstrated that the lowest corrosion rate was related to the sample with maximum explosive load thickness, and the highest corrosion spe
Mat. Res.. Publicado em: 18/12/2017
-
9. Residual Stress, Microstructure and Hardness of Thin-Walled Low-Carbon Steel Pipes Welded Manually
The aim of this work is to evaluate the welding residual stress profile in ASTM A106 Gr. B steel pipes with 4" diameter and to correlate this profile with the microstructure and hardness of the joint. The results showed that the residual stresses are more uniform for a lower welding heat input. Higher welding heat input causes not only a non-uniformity of th
Mat. Res.. Publicado em: 29/09/2016
-
10. Microstructure and Abrasion Resistance of Fe-Cr-C and Fe-Cr-C-Nb Hardfacing Alloys Deposited by S-FCAW and Cold Solid Wires
Abstract This work assesses the wear resistance behavior of different high Cr and Nb alloyed hardfacing deposits carried out by Self-shielded Flux Cored Arc Welding, considering the resulting microstructures as base for the analysis. To obtain non-commercial alloys, an “in-situ” technique was employed with addition of cold wire into the weld pool. Six co
Soldag. insp.. Publicado em: 2016-09
-
11. Comportamiento Tribológico y Microestructural en Recubrimientos Aplicados por GTAW y HVOF (Proceso Térmico de Espreado) y Usado en Recuperación de Aceros Grado Herramienta AISI/SAE D2
Abstract The Fe-Cr-Mo alloys are use in covers to protect the components that are under wear and corrosion. The high velocity thermo spray covering by HVOF (high velocity oxi-fuel) in Fe-Cr-Mo alloys has reported as a good result in projection fields for the steel tool grade for cold work. The HOVF is an attractive method to apply covering and recuperate dia
Soldag. insp.. Publicado em: 2016-06
-
12. Designing of CK45 carbon steel and AISI 304 stainless steel dissimilar welds
Gas tungsten arc welding of CK45 and AISI304 stainless steel was performed through preparation of different types of samples using ER308L and ERNi-1 wires. Welded samples were studied by different techniques including optical metallography, scanning electron microscopy equipped with energy dispersive X-ray spectroscopy (SEM-EDS), X-ray diffraction, hardness
Mat. Res.. Publicado em: 11/10/2013