Aluminum Reduction
Mostrando 1-12 de 143 artigos, teses e dissertações.
-
1. ENHANCED REMOVAL OF PERSISTENT CONTAMINANTS AND TOXICITY REDUCTION THROUGH THE APPLICATION OF A TRIPLE-STAGE FENTON PROCESS TO SANITARY LANDFILL LEACHATES FROM YUCATAN, MEXICO
Sanitary landfill leachate (SLL) is a mixture of highly toxic and recalcitrant pollutants that threatens the water quality of the Yucatán Peninsula karst aquifer, one of the most extensive aquifers on the planet. To reduce the adverse environmental impacts of this wastewater, a triple-stage Fenton process (FP) was applied in an old SLL. Removal efficiencies
Química Nova. Publicado em: 2022
-
2. A SIMPLE GREEN REDUCTION STRATEGY TO SUBSTITUTE CADMIUM IN ANALYTICAL REDUCTION OF NITRATE IN GRIESS–ILOSVAY METHOD
Nitrate is an abundant ion that is present in many industrialized products and the environment. Various analytical methods have been described using the Griess-Ilosvay reagent for the determination of nitrate in different matrices after its reduction to nitrite, in most cases with metallic cadmium as the reducer. This work proposes a new method using aluminu
Quím. Nova. Publicado em: 2021-02
-
3. Catalytic Dehydration of Glycerol to Acrolein over Aluminum Phosphate Catalysts
Gas phase conversion of glycerol to acrolein over a variety of aluminum phosphate (AlP) catalysts synthesized by a simple replacement reaction method with a variation in calcination temperature (300-700 ºC, AlP-300, AlP-400, AlP-500, AlP-600, and AlP-700, respectively) has been investigated. The textural properties, acidities and coke contents of the sample
J. Braz. Chem. Soc.. Publicado em: 2020-08
-
4. NEGATIVE EFFECTS ON PHOTOSYNTHESIS AND CHLOROPLAST PIGMENTS EXPOSED TO LEAD AND ALUMINUM: A META-ANALYSIS
ABSTRACT Toxic metals have become some of the main abiotic agents that influence the stress of organisms due to their numerous agricultural and industrial uses that result in bioaccumulation and toxicity at different levels, depending on the type and concentration in the environment. Aluminum and lead are present as a result of anthropogenic activities and c
CERNE. Publicado em: 2020-06
-
5. MORPHOPHYSIOLOGICAL AND NUTRITIONAL BEHAVIOR OF Hymenaea stigonocarpa Mart. ex Hayne (FABACEAE) SEEDLINGS SUBMITTED TO LIMING
RESUMO A calagem é benéfica para as plantas por promover a elevação do pH, neutralização do alumínio tóxico, aumentar o fornecimento de cálcio (Ca²+) e magnésio (Mg²+) e propiciar maior sistema radicular. No entanto, sabe-se que as espécies, principalmente nativas do Cerrado, respondem de formas distintas a essa técnica. Diante do exposto, o ob
Rev. Árvore. Publicado em: 25/11/2019
-
6. EFFECT OF ALUMINUM SULFATE AND CATIONIC POLYMER ADDITION IN THE MIXED LIQUOR OF A SUBMERGED MEMBRANE BIOREACTOR (SMBR): SLUDGE CHARACTERISTICS AND ORTHOPHOSPHATE REMOVAL IN BATCH EXPERIMENTS
Abstract Submerged Membranes Bioreactors (SMBR) are an established technology for wastewater treatment for water recovery and reuse. However, its routine application is still compromised by the high energy consumption to overcome the fouling effect. This study evaluated the effect of aluminum sulfate and cationic polymer in the orthophosphate removal and slu
Braz. J. Chem. Eng.. Publicado em: 30/09/2019
-
7. Potencial antimicrobiano de diferentes retentores intrarradiculares frente a Enterococcus faecalis: uma avaliação in vitro
Resumo Introdução O tratamento endodôntico tem como objetivo erradicar microrganismos bacterianos e fúngicos do canal radicular, ou pelo menos possibilitar sua redução para níveis compatíveis com a saúde do tecido perirradicular, uma vez que, após o tratamento endodôntico, colônias de microrganismos residuais podem estar presentes nos túbulos d
Rev. odontol. UNESP. Publicado em: 23/09/2019
-
8. Corrosion Behavior of AA7075-T73 Aluminum Alloy During Machining of Aeronautical Components
Corrosion of AA7075-T73 aluminum alloy during machining process was studied. An experimental device was proposed in order to simulate machining procedure. A design of experiments - DOE was used in order to evaluate what process parameter is significant. Some electrochemical tests based on open-circuit potential vs time measurements and potentiodynamic polari
Mat. Res.. Publicado em: 01/07/2019
-
9. Obtaining and characterizing dental hybrid composites with clay or silica nanoparticles and boron-aluminum-silicate glass microparticles
Abstract The aim of the present work was the obtaining and characterization of dental hybrid composites using nanoparticles (clay or silica) and boron-aluminum-silicate microparticles. We evaluated the dispersion of the nanofillers when changing their loading among 2.5%, 5%, 10% and 25% wt. Were tested, in the above quantities, four different types of nanofi
Polímeros. Publicado em: 27/06/2019
-
10. Analysis of the densification of a composite obtained by sintering process of aluminum bronze powders with different carbides
Abstract Aluminum bronze alloy is applied in environments that require materials of high mechanical resistance and wear, such as marine, oil & gas and aerospace ones. This study analyzes the densification of composites based on aluminum bronze with additions of the vanadium (VC) and niobium (NbC) carbides, and the influence of these carbides in the milling e
REM, Int. Eng. J.. Publicado em: 19/06/2019
-
11. Softening Behavior During Annealing of Overaged and Cold-rolled Aluminum Alloy 7075
This work proposes studying the softening kinetics of aluminum alloy 7075-T6. Firstly, AA 7075 strips were overaged (300°C and 5 hours). Then, the overaged strips were cold-rolled at room temperature (45% in thickness reduction) and, after that, annealed at different temperatures (200°C and 250°C) and time intervals (30 minutes - 4 hours). By using polari
Mat. Res.. Publicado em: 30/05/2019
-
12. Determination of Barreling of Aluminum Solid Cylinders During Cold Upsetting Using Genetic Algorithm
ABSTRACT This study presents Genetic Programming models for the formulation of barreling of aluminum solid cylinders during cold upsetting based on experimental results. The maximum and minimum radii of the barreled cylinders having different aspect ratio (d/h= 0.5, 1.0 and 2.0) were measured for various frictional conditions (m=0.1-0.4). The change in radii
Matéria (Rio J.). Publicado em: 20/05/2019